manualshive.com logo in svg

Bose Panaray MSA12X, Руководство по конструкции

Поделиться
Скачать
Bose Panaray MSA12X Скачать руководство пользователя страница 24

24 - Design Guide

CSD Properties and Operation

Beam Gain & EQ

Beam Gain: 

Gain for each beam.

Show Beam EQ: 

Indicates the Beam EQ. A Beam EQ is a filter that compensates the tonal balance of each 

beam corresponding to the beam shape. The filter curve is automatically computed and updated every 

time the beam pattern is sent from Modeler. You can change the curve shape manually and store to a 

Beam Preset.

Freq: 

Center frequency.

Slope:

 Slope of the curve.

Gain:

 Hi-boost gain.

Restore Defaults:

 Return to the setting that was originally suggested from Modeler for that beam pattern.

Bypass:

 Bypass the beam EQ filter.

Status

Connected: 

Blue, when the connection between the array and CSD is active.

Standby:

 Red, when the array is in Standby. You can toggle the standby status by clicking the icon.

Health: 

Yellow, if there is a temperature warning. Red if there is a temperature fault or a driver fault. Green 

otherwise.

Limit:

 Yellow, when output limiter is active for the array.

Level Meter:

 Level of input signal after the input Gain. 

Hardware Configuration

Identify:

 When Dante® is enabled and the device is online, clicking this button triggers a flashing LED on 

the back of the array.

IP Address:

 IP address of the MSA12X array. ‘Set…’ opens the Dante Properties window when Dante 

connection is enabled.

Advanced…: 

Opens the Advanced Window.

Содержание Panaray MSA12X





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды