Bosch WORCESTER DANESMOOR UTILITY 12/14 Скачать руководство пользователя | Manualshive

Страница: 24 / 28

background image

24

(b) Remove the burner box cover by pulling forwards to

release the ball studs. This will be found easier by pulling
on one side of the handle first to release two of the ball
studs and then repeating on the other side. Take care not
to pivot the remaining two ball studs too far around as
this will cause damage to the spring clips.

(c) Disconnect the burner plug-in connector by removing the

electrical facia and pulling the three-pin connector free.

Slide the locating bush from the electrical box.

(d) Feed the electrical lead back through the grommet seal to

give sufficient play to allow withdrawal and inspection of
the burner.

(e) Slacken the two M6 burner locking screws, using a 5mm

Allen key, and remove the burner.

(b) 15/19

(c) 20/25 and 26/32

ENSURE THAT ALL BAFFLES ARE SEATED IN POSITION

(a) 12/14

Baffle
retainer

Baffle

Baffle

Heat
shield

Fig. 24

Location of Boiler Flueway Baffles.

Baffle
retainer

Cap
retainer

Transit
retainer

(remove & discard)

Cap

Baffle

Heatshield

Burner
Mounting
Flange

(d) 32/50

Baffle
retainer

Cap
retainer

Top Baffle
(The tabs on the
baffle must be
positioned at the
front of the boiler)

Baffle

Heatshield

Burner
Mounting
Flange

Cap

(e) 50/70

«
...
22
23
24
25
26
...
»

Содержание WORCESTER DANESMOOR UTILITY 12/14





























Отзывы:

Нет отзывов

Похожие инструкции для WORCESTER DANESMOOR UTILITY 12/14

Vitodens 050-W BP JD

Бренд: Viessmann Страницы: 92

ecoFIT sustain 415

Бренд: Vaillant Страницы: 52

Бренд: Unical Страницы: 76

Caldariello Condens 25 KIS

Бренд: Riello Страницы: 55

Бренд: HWAM Страницы: 36

Бренд: IBC Страницы: 68

Бренд: Boulter Buderus Страницы: 40

Aerco Benchmark OMM-0116

Бренд: Watts Страницы: 126

Бренд: Raypak Страницы: 6

Бренд: Garland Страницы: 2

Бренд: Garland Страницы: 16

Бренд: Qualtex Страницы: 9

Greenstar Heatslave 18/25

Бренд: Worcester Страницы: 20

Бренд: Worcester Страницы: 36

Бренд: Worcester Страницы: 96

Бренд: Worcester Страницы: 100

Centora green 24 Nat

Бренд: Chaffoteaux & Maury Страницы: 24

Бренд: Chaffoteaux & Maury Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды