Bosch WFMC32 Скачать руководство пользователя страница 5

Страница: 5 / 27

Rev 0 (1/17/08)

Disassembly

–

Tub, Drum & Dampers

HINT:

Unlike WFL2060 & WFR2460 washers,

clips

hold tubs together –

drilling or cutting is needed.

Outer drum (tub)

The tub consists of two durable

Polinox

plastic shells

screwed to each other.

To remove outer tub:

Disconnect wire harnesses (as needed) – wire ties
can be cut off, but clips shouldn’t be cut.

Remove front panel, rear panel, fascia panel (with
detergent dispenser) and top panel.

Remove door seal, top counterweight and both side
counterweights.

Disconnect dampers from tub and slip belt off of tub.

Remove tub through

rear

of washer.

Remove (18) T-25 Torx screws holding front & rear
tubs together.

HINT:

When installing outer tub bolts, screw them in by

hand onto the first thread. Do not overtighten or cross-
thread them.

NOTE:

Rear drum bearings are factory press fit into

rear outer tubs and cannot be removed or serviced.

Removing

tub screws

Damper

Removing front of tub

T-25 screws

Comparing

tub resins

All washers starting with index __/04 have new resin tubs, front
and rear, with a translucent beige-tan color compared to older
blue-white tubs. To avoid leaking, tubs

must

have the same

resin front and rear, whether older blue-white tubs or new
beige-tan tubs – front/rear tub resin types cannot be mixed.

NOTE: You can see your fingers through new resin tubs

Old

New

702_58300000133618_ara_en_a

Содержание WFMC32




























Результаты поиска

Содержание WFMC32

Отзывы:

Похожие инструкции для WFMC32

Бренды по названию

Популярные бренды

Bosch WFMC32, Руководство по ремонту

Результаты поиска

Содержание WFMC32

Отзывы:

Похожие инструкции для WFMC32

Бренды по названию

Популярные бренды