Bosch WFMC32 Скачать руководство пользователя страница 18

Страница: 18 / 27

Rev 0 (1/17/08)

WFMC Service Tips

–

Test Program (1B): Starting

WFMC64/84 Test Program

WFMC64/84

washer test programs self-diagnose problems, including listing the last

fault codes

from the control module & the last

fault codes from the motor control. The tests are easy to

use, speeding up and simplifying diagnosing washer issues.

Entering & using WFMC64/84 test programs:

•

To reset, rotate

cycle selector knob

Off

position.

• To enter test program, push and hold

Menu

and

Select

buttons at the same time, then rotate

cycle

selector knob ccw

Permanent Press Cold

position. Hold

Menu

and

Select

buttons until

P1:

Errors

shows in display.

• To select tests, push

Menu

button (to scroll through tests) until desired test shows in display

(P1 -

P17)

Start/Pause

light will flash.

• To start tests, push

Start/Pause

button while its light is flashing -- light stays lit when test has

started. To end tests, push

Menu

button.

•

To exit test program, rotate

cycle selector knob

Off

position.

NOTE:

Door locks

for all water fill and
drain tests.

HINT:

Start/Pause

light

doesn’t come on for
some tests, door is
open. Turn off
washer, then close
door.

WFMC84

P1:ERRORS

702_58300000133618_ara_en_a

Содержание WFMC32




























Результаты поиска

Содержание WFMC32

Отзывы:

Похожие инструкции для WFMC32

Бренды по названию

Популярные бренды

Bosch WFMC32, Руководство по ремонту

Результаты поиска

Содержание WFMC32

Отзывы:

Похожие инструкции для WFMC32

Бренды по названию

Популярные бренды