Bosch VG5 700 Series Скачать руководство пользователя страница 57

Страница: 57 / 82

AutoDome 700 Series IP PTZ Camera

Configuring the AutoDome 700 Series | en

Bosch Security Systems, Inc.

User Manual

F.01U.273.798 | 3.0 | 2012.08

Idle State

Specify either

Open

Closed

idle state.

Operations Mode

Select one of the following modes for operation: Bistable, 0.5 s, 1 s, 5 s, 10 s, or 60 s.

Relay Follows

Select one of the following actions that the AutoDome performs after the relay is triggered:

–

Off

–

Connection

–

Video Alarm 1

–

Motion Alarm 1

–

Local Input 1

–

Remote Input 1

Relay Name

Type an optional name for the relay connection, up to 20 characters.

Trigger Relay

Click the

Relay 1

button to test the relay connection.

4.48

Advanced Mode: Network

4.49

Network Access

The settings on this page are used to integrate the AutoDome 800 Series into an existing

network.

Some changes only take effect after the unit is rebooted. In this case, the

Set

button changes

Set and Reboot

Make the desired changes.

Click the

Set and Reboot

button. The AutoDome 800 Series is rebooted and the changed

settings are activated.

Automatic IP assignment

If a DHCP server is employed in the network for the dynamic assignment of IP addresses, you

can activate acceptance of IP addresses automatically assigned to the AutoDome 800 Series.

Certain applications (VIDOS, Bosch Video Management System, Archive Player, Configuration

Manager) use the IP address for the unique assignment of the unit. If you use these

applications, the DHCP server must support the fixed assignment between IP address and

MAC address, and must be appropriately set up so that, once an IP address is assigned, it is

retained each time the system is rebooted.

4.49.1

IPv4

IP address

Enter the desired IP address for the AutoDome 800 Series in this field. The IP address must

be valid for the network.

Subnet mask

Enter the appropriate subnet mask for the selected IP address here.

CAUTION!

If you change the IP address, subnet mask or gateway address, the AutoDome 800 Series is

only available under the new addresses after the reboot.

Содержание VG5 700 Series



















































































Результаты поиска

Содержание VG5 700 Series

Отзывы:

Похожие инструкции для VG5 700 Series

Бренды по названию

Популярные бренды

Bosch VG5 700 Series, Руководство пользователя

Результаты поиска

Содержание VG5 700 Series

Отзывы:

Похожие инструкции для VG5 700 Series

Бренды по названию

Популярные бренды