manualshive.com logo in svg

Bosch VG4 Series, Руководство по установке

Поделиться
Скачать
Bosch VG4 Series Скачать руководство пользователя страница 60

60

en | Installing Roof Parapet and Pipe Mounts

VG4 Modular Camera Series

F.01U.216.010 | 8.0 | 2011.02

Installation Manual

Bosch Security Systems, Inc.

3.7.1

Wiring for Multiple AutoDomes

To wire multiple AutoDomes in a series, or “daisy chaining,” you must apply a terminating 

resistor to the last dome of the series. The Interface Board is supplied with a 100 

?

 

terminating resistor located between the Biphase terminals C- and C+ (pins 1 and 2) of the 

P105 control connector (see item 5 in 

Figure 3.10

 above). Remove the resistor from all but the 

last AutoDome Interface Board. The maximum number of AutoDomes that can be daisy 

chained is four (4).If using the RS485 protocol for control, switch the terminating resistor 

from the Biphase C+ and C- terminals to the RxD+ and TxD- terminals (pins 4 and 5) of the 

P105 control connector for the last dome (see item 6 in 

Figure 3.10

 above).

3.7.2

Connecting Wires to the Pipe Interface Board

The Pipe Interface Board contains all of the connectors for control, data, image, and power 

wires. Follow the procedures below to make the proper connections.

1.

Attach a BNC connector to the video coax cable and connect it to its mating connector 

J102 on the Pipe Interface Board. If using UTP for video or Ethernet, attach an RJ45 

connector plug to the e UTP cable and connect the plug to its mating connector J101 on 

the Pipe Interface Board.

Ref. Description

Connector

Wire Gauge

Pin

Description

1

Pipe Interface Module

2

Video Coax In

J102

3

6-pin Connector Alarms In (3-7)

P103

4

4-pin Connector Alarms Out (1-3)

P102

5

100 

?

 Resistor

P105

6

Data In/Out

P105

AWG 26-16

1

Biphase (C-)

2

Biphase  (C+)

3

Earth Ground

4

RxD  +

5

TxD -

6

Signal Ground

7

Alarms In (EOLR Supervised, 1-2)

P104

AWG 26-16

7

Ground

6

Alarm 2

5

Alarm 1

4

Earth Ground

8

Relay Output

P104

AWG 26-16

3

Normally Closed

2

Common

1

Normally Open

9

Dome Power

P101

AWG 18-14

3

Dome 24 VAC

2

Earth Ground

1

Dome  24  VAC

10

Heater Power

P107

AWG 18-14

2

Heater 24 VAC

1

Heater 24 VAC

11

RJ45 Ethernet or UTP Video

J101

12

To AutoDome

WARNING! 

Use a 24 VAC Class 2 power supply only.

WARNING! 

Do not connect the RJ45 connector unless using UTP video or Ethernet. This connection 

causes video distortion.

Содержание VG4 Series













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды