Bosch VG4 Series Скачать руководство пользователя

Страница: 37 / 108

VG4 Modular Camera Series

Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en

Bosch Security Systems, Inc.

Installation Manual

F.01U.216.010 | 8.0 | 2011.02

2.11.3

VG4 Pressurized Environmental Mounting Options

The VG4 Pressurized Environmental Housing must be mounted to the appropriate VG4

mounts. The mounts for the Pressurized Environmental Housing have been modified to

remove the guide pins that serve as installation aids. You must mount the Pressurized

Environmental Housing to one of these mounts:

Type Number

Pressurized Environmental Housing Mounting Option

VG4-A-9543N Pipe

mount

VG4-A-PA0N Pendant

arm

mount

VG4-A-PA0FN

Pendant arm mount with fiber optic module

VG4-A-PA1N

Pendant arm mount with 120 VAC transformer

VG4-A-PA1FN

Pendant arm mount with fiber optic module and 120 VAC transformer

VG4-A-PA2N

Pendant arm mount with 230 VAC transformer

VG4-A-PA2FN

Pendant arm mount with fiber optic module and 230 VAC transformer

CAUTION!

DO NOT mount a VG4 Pressurized Environmental Housing to a traditional VG4 mounting

option. The traditional mounting options contain guide pins that are not compatible with the

Pressurized Environmental Housing. Refer to item 1 on the images below:

If your pendant arm or pipe mount contains these pins,

DO NOT

attempt to mount a

Pressurized Environmental Housing to these mounts. You must either return the mounts to

have the pins removed or order the appropriate mounting option for the Pressurized

Environmental Housing. Contact you local Bosch Security Systems customer service

representative.

Содержание VG4 Series













































































































Результаты поиска

Содержание VG4 Series

Отзывы:

Похожие инструкции для VG4 Series

Бренды по названию

Популярные бренды

Bosch VG4 Series, Руководство по установке

Результаты поиска

Содержание VG4 Series

Отзывы:

Похожие инструкции для VG4 Series

Бренды по названию

Популярные бренды