Bosch SMT500 Скачать руководство пользователя страница 10

Страница: 10 / 12

1 0

| Operating Instructions |

SMT500 Leak Detector

SP01501467 | REV A | 4.2021

Bosch Automotive Service Solutions Inc

Troubleshooting

Problem

Solution

No green light

•  Check polarity
•  Ensure 12-volt battery is fully charged
•  Reconnect power cables

Green light flashing

•  Power supply must be between 11.5 and 14 VDC
•  Connect to a fully charged 12-volt battery
•  Never use battery charger as power source

Amber or red light flashing

• Open circuit/internal component
• Contact technical support

No air flow

•

Open the flow control valve

• Ensure hoses are not kinked or pushed into machine

Insufficient vapor

•

Check fluid level

•

Open the flow control valve

• Ensure hoses are not kinked or pushed into machine

Flow meter ball sticking

•

Tap face of flow meter

•

If problem persists, clean flow meter

Gauge bouncing or flow meter

bouncing

Drain vapor hose

High pressure reading

Ensure hoses are not kinked or pushed into machine

Содержание SMT500













Результаты поиска

Содержание SMT500

Отзывы:

Похожие инструкции для SMT500

Бренды по названию

Популярные бренды

Bosch SMT500, Руководство по эксплуатации

Результаты поиска

Содержание SMT500

Отзывы:

Похожие инструкции для SMT500

Бренды по названию

Популярные бренды