Bosch Rexroth R-IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 82

Страница: 82 / 96

Planning

/94

Bosch Rexroth AG

DOK-CONTRL-ILPSDO8****-AW04-EN-P

Rexroth Inline Module with Safe Digital Outputs R-IB IL 24 PSDO 8-PAC

14.1

Planning

Checklist for planning the use of the safety module

Device type/equipment identification

Version: HW/FW/FW

Date

Editor

Test engineer

Remark

No. Requirement (mandatory)

Yes

Remark

Has the current module application description been used as the basis

for planning?

Revision:

Are the actuators approved for connection to the module (according to

the technical data and parameterization options)?

Has the voltage supply been planned according to the specifications for

the protective extra-low voltage in accordance with PELV?

Has the power supply of U

and U

from a power supply unit been

planned?

Is external fuse protection of the module planned (according to the

specifications in this application description for supply voltage U

Are measures planned to prevent simple manipulation?

Are measures planned to prevent connectors being mixed up?

Are requirements for the actuators and cable installation observed

according to the SIL/SIL CL/Cat./PL to be achieved and is the

corresponding implementation planned?

Are the specifications for the parameterization for each channel

specified?

Are test intervals specified for testing the shutdown capability of the

actuators, if this is required to achieve a SIL/SIL CL/Cat./PL?

Has it been ensured that any person intentionally starting hazardous

movements has a direct view of the danger zone?

Does the planned use correspond to the intended use?

Are the ambient conditions observed according to the technical data?

Have test intervals been defined?

Has the switch-off delay for stop category 1 been observed in the

calculation of the total response time for the machine/system?

No. Requirement (optional)

Yes

Remark

Have specifications for assembly and electrical installation been

defined (e.g., EPLAN) and communicated to the relevant personnel?

Have specifications for startup been defined and communicated to the

relevant personnel?

Date

Signature (editor)

Date

Signature (test engineer)

Содержание Rexroth R-IB IL 24 PSDO 8-PAC

































































































Результаты поиска

Содержание Rexroth R-IB IL 24 PSDO 8-PAC

Отзывы:

Похожие инструкции для Rexroth R-IB IL 24 PSDO 8-PAC

Бренды по названию

Популярные бренды

Bosch Rexroth R-IB IL 24 PSDO 8-PAC, Руководство пользователя

Результаты поиска

Содержание Rexroth R-IB IL 24 PSDO 8-PAC

Отзывы:

Похожие инструкции для Rexroth R-IB IL 24 PSDO 8-PAC

Бренды по названию

Популярные бренды