Bosch rexroth MSK 030 Скачать руководство пользователя страница 62

Страница: 62 / 72

Troubleshooting

12.1

Troubleshooting procedure

As a matter of principle, the instructions in the project planning and commis‐

sioning manuals must be followed in case of failures and errors. Contact the

manufacturer, if necessary.

Malfunctions

Error cause

Measures

Motor does not run

Controller enable signal missing

Activate controller enable signal

Controller fault

Troubleshoot acc. to documentation of

controller

Voltage supply missing

Control voltage supply

Brake is not released

Check the brake activation

Vibrations

Coupling elements or attachments are

poorly balanced

Re-balance

Adjustment of shaft end attachments

(coupling, gearbox, ...) is insufficient

Re-align the attachments

Mounting screws loose

Lock screw connections acc. to specifi‐

cations

Running noise

Foreign bodies within the motor

Stop the motor --> repair by manufac‐

turer

Bearing is damaged

Stop the motor --> repair by manufac‐

turer

High motor temperatures
Motor temperature monitoring is activa‐

ted

Operation outside of rated data

Reduce load and check the dimension‐

ing

Heat dissipation is impaired

Clean the motor
For fan units, clean fan grille and check

the fan function
For liquid cooling, check cooling circuit.

Wrong or defective temperature display Temperature sensor not connected

Connect temperature sensor

Temperature sensor defective

Stop the motor --> repair by manufac‐

turer
Connect the backup temperature sen‐

sor, if any is available.

Tab. 12-1:

Measure at malfunction on MSK motors

48/57

Troubleshooting

MSK Synchronous Servomotors

Bosch Rexroth AG R911325169_Edition 03

Содержание rexroth MSK 030









































































Результаты поиска

Содержание rexroth MSK 030

Отзывы:

Бренды по названию

Популярные бренды

Bosch rexroth MSK 030, Руководство по эксплуатации

Результаты поиска

Содержание rexroth MSK 030

Отзывы:

Бренды по названию

Популярные бренды