Bosch rexroth MSK 030 Скачать руководство пользователя страница 17

Страница: 17 / 72

Safety instructions

2.1

About this product

Observe the general safety notes in this chapter and the safety instructions in

this documentation. Therewith, you avoid personal danger, damage and er‐

rors.

This operating instruction must be stored and transferred in case

of sale during the complete product lifetime.

2.2

Indented use

Prerequisites for proper and safe use of the motors are proper transport, ap‐

propriate storage, proper assembly and connection, careful maintenance, op‐

eration and overhaul.
The motors have been designed for installation in industrial machinery. The

motors are according to the following standards and directives.
Standards

EN 60034-1

Rating and performance behavior

EN 60034-5

Type of protection

Directives

2006/95/EG

Low Voltage Directive (valid until April 19, 2016)

2014/35/EU

Low Voltage Directive 2014/35/EU (valid from April 20, 2016)

The machine manufacturer must evaluate the electric and mechanic safety

as well as environmental influences in the assembled state of the machine

according to the Machine Directive 2006/42/EC and DIN EN 60204-1 (safety

of machines).
The electrical installation must comply with the protection requirements of

EMC Directive 2014/30/EU. The plant manufacturer is responsible for appro‐

priate installation (for example: physical separation of signal and power ca‐

bles, using shielded cables, ...). The EMC instructions of the converter manu‐

facturer must be observed.
The machine may not be commissioned before conformity with these direc‐

tives has been confirmed.

2.3

Unintendend use

Any use of the MSK motors outside of the specified fields of application or

under operating conditions and technical data other than those specified in

this documentation is considered to be "inappropriate use".
Unless explicitly provided for this purpose, the motors may not be used in ex‐

plosion-hazardous areas (compare housing design -NSNN).
Direct operation on the three-phase network is forbidden.

2.4

Qualification of personnel

For the purpose of this manual, qualified personnel means persons who are

familiar with transporting, installing, mounting, commissioning and operating

the components of the electrical drive and control system and the associated

hazards and have an appropriate qualification for their job.

MSK Synchronous Servomotors

3/57

Safety instructions

R911325169_Edition 03 Bosch Rexroth AG

Содержание rexroth MSK 030









































































Результаты поиска

Содержание rexroth MSK 030

Отзывы:

Бренды по названию

Популярные бренды

Bosch rexroth MSK 030, Руководство по эксплуатации

Результаты поиска

Содержание rexroth MSK 030

Отзывы:

Бренды по названию

Популярные бренды