Bosch Rexroth lndraDrive HCS02 Series Скачать руководство пользователя страница 293

Страница: 293 / 382

CAUTION

Damage caused by voltage arcing!

Insulate ring terminals and connecting lines with a heat-shrinkable sleeve. Af‐

terwards only strip the insulation of the contact surface of the ring terminal.

The cross section of the lines must be at least 10 mm

, but mustn't be smaller

than the cross section of the supply feeder at mains connection X3.
The dielectric strength of the single strand must be at least 750 V (e.g. strand

type H07).

8.19

XS1, Shield Connection Control Lines

CAUTION

Risk of damage caused by high temperature of the outgoing air!

Observe outlet temperatures at the top of the devices.

Always connect the shields with the largest possible metal-to-metal

contact surface.

Fig.8-59:

Shield connection XS1 (control lines)

Function

Connection point for the shields of lines connected to the control section and

of which the connectors do not have their own shield connection.

8.20

XS2, Shield Connection Motor Cable

CAUTION

Risk of damage to the drive controller caused by too long screws!

Exclusively use screws of a maximum length of 12 mm for the thread of shield

connection XS2.

Project Planning Manual | Rexroth IndraDrive

Electric Drives

and Controls

| Bosch Rexroth AG 283/369

Functions and Electrical Connection Points

Содержание Rexroth lndraDrive HCS02 Series































































































































































































































































































































































































Результаты поиска

Содержание Rexroth lndraDrive HCS02 Series

Отзывы:

Похожие инструкции для Rexroth lndraDrive HCS02 Series

Бренды по названию

Популярные бренды

Bosch Rexroth lndraDrive HCS02 Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth lndraDrive HCS02 Series

Отзывы:

Похожие инструкции для Rexroth lndraDrive HCS02 Series

Бренды по названию

Популярные бренды