Bosch Rexroth IndraControl XFE01.1-SY-01 Скачать руководство пользователя

Страница: 29 / 52

●

Mounting rail
Mount the extension modules on a 35 mm standard mounting rail. The

preferred overall height of the mounting rail is 7.5 mm (corresponds to TH

35-7.5 acc. to EN 60715).
Mount the extension module as described in this chapter.
The fastening distance of the mounting rails may not exceed 200 mm. This

distance is required to ensure stability while mounting and demounting the

control or the IndraControl extension modules

< 200

Fig. 10-2: Mounting rail fastening (in mm)

Electronic damage due to fastening elements
of the mounting rail

NOTICE

If screws and rivets are too high on the mounting rail, the bus base modules

do not really engage on the mounting rail. Use only screws and rivets with a

structural height of up to 3 mm to fasten the mounting rail.

●

End clamps
Fasten end clamps on both sides of the IndraControl XM station. End clamps

guarantee the correct fastening of the control and the modules connected to

them on the mounting rail and they are used as lateral end elements

●

Do not wire cables parallel to motor cables over a long distance or other

strong interference sources to avoid coupling of interferences

●

The LED displays may not be hidden

●

Wire all connecting cables in loops

●

Use strain reliefs for all cables

●

Keep the maximum distance possible from interference sources

●

Ensure the minimum distances for sufficient ventilation as specified in the

operating instructions of the XM control. (refer to

chapter 1.5 "Related

documents" on page 2

)

In case of a several line design, the supply air has to be measured under each

line and its limit value has to be observed. For information on ambient

temperatures, refer to

chapter 6 "Ambient conditions" on page 8

●

Additionally, provide sufficient distance for mounting, demounting, plugs and

cables

IndraControl XFE01.1-SY-01 Safety Ex-

tension Module

23/45

Mounting, demounting and electric installation

R911376654_Edition 03 Bosch Rexroth AG

Содержание Rexroth IndraControl XFE01.1-SY-01





















































Результаты поиска

Содержание Rexroth IndraControl XFE01.1-SY-01

Отзывы:

Похожие инструкции для Rexroth IndraControl XFE01.1-SY-01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl XFE01.1-SY-01, Руководство по эксплуатации

Результаты поиска

Содержание Rexroth IndraControl XFE01.1-SY-01

Отзывы:

Похожие инструкции для Rexroth IndraControl XFE01.1-SY-01

Бренды по названию

Популярные бренды