Bosch Rexroth IndraControl XFE01.1-SY-01 Скачать руководство пользователя

Страница: 39 / 52

12.2.1 "Conf" pushbutton

Press the "Conf" pushbutton once to confirm the established communication

between the programming system and the Safety extension module upon initial

Safety extension module IndraControl XFE01.1-SY-01 and not accidentally to a

different Safety module.

12.2.2 LED display

The display LED indicates the following:

LED

Color and status

Description

Pwr

Off

No power supply from the standard control present

Red

Error: The voltage monitoring of the Safety function module

IndraControl XFE01.1-SY-01 switched off the safe logic

voltage

Green

All internal voltages of the Safety extension module

IndraControl XFE01.1-SY-01 are within the permitted range

Error

Off

The Safety extension module IndraControl XFE01.1-SY-01 is

ready

Red

The Safety extension module IndraControl XFE01.1-SY-01 is

not ready. This LED is on during the initialization phase.
If the LED is still on after the initialization (approx. 1 min) or

if the LED is permanently switched on at runtime, integrated

self-tests determined a "fatal error" (e.g. hardware error).
The Safety extension module IndraControl XFE01.1-SY-01 is

then probably defective and has to be replaced.
Contact the Bosch Rexroth Service

Tab. 12-1: LEDs to display operational readiness

LED "Run"
(Color and status)

LED "Failure"
(Color and status)

Operating state of the Safety extension module IndraControl

XFE01.1-SY-01

Off

No power supply provided or hardware reset triggered

Off

Green

Initialization phase; first part (ca. 30 s) is running

Red

Off

Initialization phase; second part (ca. 10 s) is running

Red, flashing

Off

Ready for download.
The Safety extension module IndraControl XFE01.1-SY-01

does not contain any valid application or a download is not

yet completed

Red

Green, flashing

Request to press the "Conf" pushbutton

Red

Green

SAFETY STOP

Green

SAFETY RUN

IndraControl XFE01.1-SY-01 Safety Ex-

tension Module

33/45

Device description

R911376654_Edition 03 Bosch Rexroth AG

Содержание Rexroth IndraControl XFE01.1-SY-01





















































Результаты поиска

Содержание Rexroth IndraControl XFE01.1-SY-01

Отзывы:

Похожие инструкции для Rexroth IndraControl XFE01.1-SY-01

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl XFE01.1-SY-01, Руководство по эксплуатации

Результаты поиска

Содержание Rexroth IndraControl XFE01.1-SY-01

Отзывы:

Похожие инструкции для Rexroth IndraControl XFE01.1-SY-01

Бренды по названию

Популярные бренды