Bosch Rexroth IndraControl S20 Скачать руководство пользователя

Страница: 55 / 88

Maintaining, repairing, decommissioning and disposal

10.1

Maintenance

Module is maintenance-free.
Depending on the application and the connected periphery, the function of

the peripherals and the security chain have to be checked regularly if neces‐

sary.
The service life of the module is 20 years. At a low demand rate, it is 25

years.
Retesting is currently not required.
Maintain the connected peripherals (e.g. light grids) as described in the ven‐

dor specifications.

10.2

Repair

Repairs or user-specific changes at the module are prohibited. The housing

must not be opened. The module is protected against manipulations using

protective labels. In case of unauthorized repair or opening of the housing,

the protective label is damaged. The function of the safety module is not

guaranteed anymore in this case.
In case of error, send the module to Bosch Rexroth or contact the Bosch

Rexroth service, refer to

chapter 16 "Service and support" on page 79

10.3

Decommissioning and disposal

Decommission as described by the machine or system vendor.
Ensure the following handling of used modules when decommissioning the

Csos system or parts of the system:

Remaining of the module

Action

The modules are still used as intended.

For requirements on storage and trans‐

port acc. to the technical data, refer to

chapter 11.2 "Module data of the S20-

SSDO 8/3" on page 55

Modules are not used anymore.

Dispose modules according to the envi‐

ronmental standards. Ensure that the

modules are not used again.

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

Bosch Rexroth AG

53/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Maintaining, repairing, decommissioning and disposal

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды