Bosch Rexroth IndraControl S20 Скачать руководство пользователя

Страница: 81 / 88

Service and support

Our worldwide service network provides an optimized and efficient support.

Our experts offer you advice and assistance should you have any queries.

You can contact us 24/7.

Service Germany

Our technology-oriented Competence Center in Lohr, Germany, is responsi‐

ble for all your service-related queries for electric drive and controls.
Contact the Service Hotline and Service Helpdesk under:

Phone:

+49 9352 40 5060

Fax:

+49 9352 18 4941

E-mail:

[email protected]

Internet:

http://www.boschrexroth.com/

Additional information on service, repair (e.g. delivery addresses) and training

can be found on our internet sites.

Service worldwide

Outside Germany, please contact your local service office first. For hotline

numbers, refer to the sales office addresses on the internet.

Preparing information

To be able to help you more quickly and efficiently, please have the following

information ready:
●

Detailed description of malfunction and circumstances

●

Type plate specifications of the affected products, in particular type co‐

des and serial numbers

●

Your contact data (phone and fax number as well as your e-mail ad‐

dress)

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

Bosch Rexroth AG

79/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Service and support

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды