background image

 

General information on damage to property and damage to product 17/48

 

RE29162-XE-B/10.20, DBET.../...XE, 

Bosch Rexroth AG

3  General information on damage to 

property and damage to product

The warranty only applies to the delivered configuration.

 

• The claim to warranty expires if the product is assembled, commissioned and 

operated incorrectly, not used as intended and/or handled improperly.

 

• The following safety instructions apply to chapters 6 to 14.

NOTICE

Inadmissible mechanical load!

Impact or shock forces on the valve may damage or even destroy it.

 

Never use the valve as handle or step. Do not place/put any objects on top of it.

Dirt and foreign particles in the valve!

Penetrating dirt and foreign particles in the valve lead to wear and malfunctions. 
The safe function of the valve can no longer be ensured.

 

During installation, ensure utmost cleanliness in order to prevent foreign 
particles, such as welding beads or metal chips, from getting into the hydraulic 
lines.

 

Before commissioning, ensure that all hydraulic connections are tight and 
that all seals and caps of the plug-in connections are correctly installed and 
undamaged.

 

Do not use linting fabric for cleaning.

 

Ensure that no cleaning agents are able to penetrate the hydraulic system.

Environmentally harmful hydraulic fluid!

Leaking hydraulic fluid leads to environmental pollution.

 

Immediately remedy possible leakage.

 

Dispose of the hydraulic fluid in accordance with the currently applicable 
national regulations in your country.

Содержание Rexroth DBET

















































Отзывы: