Bosch Professional GBH 18V-40 C, Инструкция по эксплуатации

Страница: 22 / 313

22 | English
Working mode (18) indic-
ator Functions
lights up
Soft working mode: Reduced power for processing sensitive materials
– "Hammer drilling" operating mode (Electronic Precision Control soft start): Slow, strictly
controlled run-up up to reduced, low power
– Rapid Shut-off (KickBack Control) active
– "Chiselling" operating mode (Adaptive Speed Control soft start): Slow, strictly controlled
run-up up to reduced power
Connectivity functions
In conjunction with the Bluetooth ® Low Energy Module
GCY 42 , the following connectivity functions are available
for the power tool:
– Registration and personalisation
– Status check, output of warning messages
– General information and settings
– Management
Read the corresponding operating instructions for informa-
tion about the
Bluetooth ® Low Energy Module GCY 42 .
Practical Advice
u
With the Bluetooth ® Low Energy Module GCY 42, the
power tool is equipped with a radio interface. Local
operating restrictions, e.g. in aircraft or hospitals,
must be observed.
u
In areas where the Bluetooth ® wireless technology is
not allowed to be used, the Bluetooth ® Low Energy
Module GCY 42 and the button cell must be removed .
Note: The cover (15) can only be securely closed if the
Bluetooth ® Low Energy Module GCY 42 and the button cell
are situated in the power tool.
– To
deactivate the Bluetooth ® Low Energy Module
GCY 42, rotate the button cell or place means of insula-
tion between the button cell and
Bluetooth ® Low Energy
Module GCY 42.
– Close the cover (15) to prevent dirt from getting in.
Overload clutch
u
If the application tool jams or snags, the power trans-
mission to the drill spindle will be interrupted. Always
hold the power tool firmly with both hands to with-
stand the forces this may create and adopt a position
with stable footing.
u
Switch the power tool off immediately and remove the
application tool if the power tool becomes blocked.
Switching on when the drilling tool is blocked may
cause high torque reactions.
Rapid shut-off (KickBack Control)
The rapid shut-off function (KickBack
Control) gives the user greater control
over the power tool and offers them bet-
ter protection than power tools that do
not have Kickback Control. If the power
tool suddenly and unforeseeably rotates
around the drilling axis, it will switch off,
the rapid shut-off indicator (17) will light
up red and the worklight (11) will flash.
When rapid shut-off is activated, the
status indicator
(20) flashes red.
– To switch the tool back on , release the on/off switch (9)
and then press it again.
Electronic Precision Control (EPC)
EPC assists you when drilling and when working with impact
in sensitive materials by ensuring slow start-up of the operat-
ing speed for precise working.
Adaptive Speed Control in "Chiselling" Operating Mode
For better control and precise position-
ing, the power tool starts at a low speed
and then increases to the set speed.
Adapted Speed Control is started up
automatically when the power tool is
switched on.
Vibration damping
The integrated vibration damping function re-
duces the generated vibration.
u
Do not continue to use the power tool if the damping
element is damaged.
Maintenance and Service
Maintenance and Cleaning
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
u
To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
u
Replace a damaged dust protection cap immediately.
It is recommended that you have use an after-sales
service for this.
– Clean the tool holder (2) after each use.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at:
www.bosch-pt.com
The Bosch product use advice team will be happy to help you
1 609 92A 74B | (18.05.2022) Bosch Power Tools