Bosch Professional GBH 18V-40 C, Инструкция по эксплуатации

Страница: 19 / 313

English | 19
Press the button for the battery charge indicator or to
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
The state of charge of the battery is also displayed on the
user interface Status indications.
Battery model GBA 18V...
LED Capacity
3× continuous green light 60–100 %
2× continuous green light 30–60 %
1× continuous green light 5–30 %
1× flashing green light 0–5 %
Battery model ProCORE18V...
LED Capacity
5 × continuous green light 80–100 %
4 × continuous green light 60–80 %
3 × continuous green light 40–60 %
2 × continuous green light 20–40 %
1 × continuous green light 5–20 %
1 × flashing green light 0–5 %
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Assembly
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
u
Before carrying out any work on the power tool (e.g.
maintenance, tool change, etc.) as well as during
transport and storage, press the lock-on button to
lock the on/off switch. There is risk of injury from unin-
tentionally pressing the on/off switch.
Inserting the Bluetooth ® Low Energy Module
GCY 42 (Accessory)
Read the corresponding operating instructions for informa-
tion about the
Bluetooth ® Low Energy Module GCY 42 .
Auxiliary handle
u
Do not operate your power tool without the auxiliary
handle
(12) .
u
Make sure that the auxiliary handle is always
tightened.
Otherwise you could lose control of the power
tool when working.
Swivelling the auxiliary handle (see figure B)
You can swivel the auxiliary handle (12) to any angle for a
safe work posture that minimises fatigue.
– Turn the lower gripping end of the auxiliary handle
(12)
anticlockwise and swivel the auxiliary handle (12) into
the required position. Then turn the lower gripping end of
the auxiliary handle
(12) clockwise to retighten it.
Make sure that the retaining strap of the auxiliary handle
slots into the corresponding groove of the housing.
Selecting drill chucks and tools
For hammer drilling and chiselling, you will need SDS max
tools, which insert into the SDS max drill chuck.
Changing the Tool
The dust protection cap (3) largely prevents the penetration
of drilling dust into the tool holder during operation. When
inserting the tool, make sure that the dust protection cap
(3)
does not become damaged.
u
Replace a damaged dust protection cap immediately.
It is recommended that you have use an after-sales
service for this.
Changing the Tool (SDS max)
Inserting the Application Tool (see figure C)
With the SDS-max tool holder, you can change the applica-
tion tool simply and easily without additional aids.
– Clean and lightly grease the insertion end of the applica-
tion tool.
– Insert the application tool into the tool holder while turn-
ing it until it locks automatically.
– Check the latching by pulling the tool.
Removing the application tool (see figure D)
– Push the locking sleeve (4) back and remove the applica-
tion tool.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one’s
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Bosch Power Tools 1 609 92A 74B | (18.05.2022)