manualshive.com logo in svg

Bosch PRAESENSA PRA-AD604, Руководство по настройке

Поделиться
Скачать
Bosch PRAESENSA PRA-AD604 Скачать руководство пользователя страница 53

PRAESENSA

Configure the system | en

53

Bosch Security Systems B.V.

Configuration manual

2020-09 | V1.20 | PRAESENSA 1.20

5.3.3

Multifunction power supply

1.

Below

 Device options, 

click

 Multifunction power supply:

–

A new screen appears listed the network connected multifunction power supplies.

–

Notice that a Multifunction power supply (Mps) is only listed when it is added to the
System composistion.

2.

Select and click

 the Mps name to configure:

–

A new screen appears to configure the General, Control inputs and Control outputs
functionality.

General

1.

Select and click

 the + of the General category to configure the general settings of the

Mps.

2.

Select

, 

enable

 or 

disable

 each of the following items:

Item

Value

Description

Supervision

Mains

Enable / Disable

Enable

: a mains supply disconnection will be

reported by the Mps front/rear panel
indicator(s) only when a back‑up battery is
connected (see indicator tables at the end of
this section), 

Diagnose, page 105 and Optional:

Using the Logging Viewer, page 125.

Disable:

 results in a system that does not

indicate and report a mains failure.

Battery

Enable / Disable

Enable

: a connected battery disconnection will

be reported by the Mps front/rear panel
indicator(s) (see indicator tables at the end of
this section), 

Diagnose, page 105 and Optional:

Using the Logging Viewer, page 125.

Disable:

 results in a system that does not

indicate and report battery failures.

IMPORTANT

: Battery protection is always

active when a battery is connected. When
supervision is 

disabled

 the following faults are

suppressed:
–

Battery missing fault.

–

Battery RI fault.

–

Backup available for each power supply.

The diagnostics page battery impedance is 

only

available when battery supervision is 

enabled

.

Battery capacity [Ah]

Number

Enter

 the number of the connected battery

capacity value (between 100 and 250 Ah)
which is used for the impedance measurement.
A disconnection and fault will be reported by
the Mps front/rear panel indicator(s) (see
indicator tables at the end of this section),
Diagnose, page 105 and Optional: Using the
Logging Viewer, page 125.

Содержание PRAESENSA PRA-AD604





































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды