manualshive.com logo in svg

Bosch PRAESENSA PRA-AD604, Руководство по настройке

Поделиться
Скачать
Bosch PRAESENSA PRA-AD604 Скачать руководство пользователя страница 47

PRAESENSA

Configure the system | en

47

Bosch Security Systems B.V.

Configuration manual

2020-09 | V1.20 | PRAESENSA 1.20

Front panel indicators

The front panel indicators indicate correct functionality and faults. The table following
indicates the active state.
To make device identification visible, see 

System composition, page 40.

Front panel indicators

Device fault present

Yellow

Power on

Green

Network link present
Network link lost
Standby for redundancy

Green
Yellow
Blue

Identification mode /
Indicator test

All LEDs blink

Rear panel indicators and controls

The rear panel indicators indicate correct functionality and faults. The table following
indicates the active state.
To make device identification visible, see 

System composition, page 40.

Rear panel indicators and controls

SD card busy; do not
remove

Green

100 Mbps network 
1 Gbps network

Yellow
Green

Device fault present

Yellow

Power on

Green

Device reset (to factory
default)

Button

Identification mode /
Indicator test

All LEDs blink

Refer to

–

Logon the application, page 35

–

Optional: Install Dante Controller, page 27

Содержание PRAESENSA PRA-AD604





































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды