background image

 English | 

17

Bosch Power Tools

2 609 006 340 | (23.7.12)

Mounting/Replacing the Application Tool/Accessory 

(see figures A–C)

f

Check the tight seating of the application tool/acces-

sory. 

Incorrect or not securely fastened application tools/ 

accessories can come loose during operation and pose a 

hazard.

Inserting the Tool Retainer (see figure D)

When the SDS lever 

1

 was opened too far, the tool retainer 

14

 

can fall out of the gear head.
Insert the tool retainer 

14

 into the gear head in such a manner 

that its flat side fits into the opening. Turn the SDS lever 

1

 

clockwise.

Mounting the Depth Stop

The depth stop 

12

 can be used when working with segment 

saw blades, Riff-segment saw blades and segment blades.
If required, remove an already mounted application tool/

accessory.
Slide the depth stop 

12

 over and beyond the tool holder 

8

 to 

the stop onto the gear head of the power tool with the labelled 

side facing upward.
The depth stop is intended for the following cutting depths:

– With segment saw blades ACZ 85 .. with a diameter of 

85 mm: 8 mm, 10 mm, 12 mm and 14 mm cutting depths 

(see indication on the depth stop in large font and not in 

brackets).

– With segment saw blades ACZ 100 .. with a diameter of 

100 mm: 14 mm, 16 mm, 18 mm and 20 mm cutting 

depths (see indication on the depth stop in smaller font 

and brackets).

Mount the fitting segment saw blade for the desired cutting 

depth. Turn the depth stop 

12

 in such a manner that the de-

sired cutting depth is above the section of the saw blade, with 

which the cut is to be made.
For all other cutting depths and when working with other appli-

cation tools, remove the depth stop 

12

. For this, remove the 

application tool and pull the depth stop from the gear head.

Mounting/Replacing a Sanding Sheet on the Sanding Plate

The sanding plate 

10

 is fitted with Velcro backing for quick 

and easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 

11

, free the Velcro back-

ing of the sanding plate 

10

 from any debris by tapping against 

it in order to enable optimum adhesion.
Position the sanding sheet 

11

 flush alongside one edge of the 

sanding plate 

10

, then lay the sanding sheet onto the sanding 

plate and press firmly.
To ensure optimum dust extraction, pay attention that the 

punched holes in the sanding sheet match with the holes in 

the sanding plate.
To remove the sanding sheet 

11

, grasp it at one of the tips and 

pull it off from the sanding plate 

10

.

You can use all sanding sheets, fleece pads/polishing cloth 

pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth 

pads, are attached to the sanding plate in the same manner.

Selecting the Sanding Sheet

Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:

n

If required, remove an already mounted application 

tool/accessory. For this, push SDS lever 

1

 out of the lock-

ing position and sidewards.

To release the tool retainer 

14

, turn the SDS le-

ver approx. 3 turns in anticlockwise direction.

Note: 

Do not turn the SDS lever 

1

 further than necessary, 

otherwise the tool retainer 

14

 can fall out of the gear head 

(see “Inserting the Tool Retainer”, page 17).

o

Remove the application tool/accessory.

p

Position the new application tool/accessory (e.g. plunge 

cut saw blade 

9

) with its opening above the tool retainer 

14

. Move it on the tool holder 

8

 so that the recesses of the 

application tool/accessory engage in the cams of the tool 

holder. 
To achieve a safe and low-fatigue working stance, the ap-

plication tools/accessories can be mounted on the tool 

holder in any locking position. Mount the application 

tool/accessory with the off-set facing downward (as 

shown in the figure).

q

Turn the SDS lever 

1

 clockwise to lock the tool 

retainer 

14

 and clamp the application tool/ 

accessory. Hand-tighten the SDS lever.

r

When the SDS lever is not positioned directly above the 

locking position, turn it back in anticlockwise direction 

until it is located above the locking position. In no-load, 

the SDS lever can be turned back by one turn (max.).

Turn the SDS lever until it is located directly above the 

locking position.

s

Press SDS lever 

1

 down so that it can be heard to engage 

in the locking position.

Sanding disc

Material

Application

Grain size

Red quality

– All wooden materials 

(e.g., hardwood, soft-

wood, chipboard, build-

ing board)

– Metal materials

For coarse-sanding, e.g. of rough, unplaned beams and 

boards

coarse

40

60

For face sanding and planing small irregularities

medium

80

100

120

For finish and fine sanding of wood

fine

180

240

320

400

OBJ_BUCH-1645-002.book  Page 17  Monday, July 23, 2012  8:57 AM

Содержание PMF 250 CES WEU












Отзывы: