Bosch PKS 16 Multi, Оригинальное руководство пользователя

Страница: 16 / 125

16 | English
Power tool use and care
u
Do not force the power tool. Use the correct power
tool for your application.
The correct power tool will do
the job better and safer at the rate for which it was de-
signed.
u
Do not use the power tool if the switch does not turn it
on and off.
Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
u
Disconnect the plug from the power source and/or re-
move the battery pack, if detachable, from the power
tool before making any adjustments, changing ac-
cessories, or storing power tools.
Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
u
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool.
Power
tools are dangerous in the hands of untrained users.
u
Maintain power tools and accessories. Check for mis-
alignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use.
Many accidents are caused by
poorly maintained power tools.
u
Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
u
Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed.
Use of the power tool for operations different
from those intended could result in a hazardous situation.
u
Keep handles and grasping surfaces dry, clean and
free from oil and grease.
Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
u
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This
will ensure that the safety of the power tool is maintained.
Safety instructions for circular saws
Cutting procedures
u
DANGER: Keep hands away from cutting area and
the blade. If both hands are holding the saw, they cannot
be cut by the blade.
u
Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the workpiece.
u
Adjust the cutting depth to the thickness of the work-
piece.
Less than a full tooth of the blade teeth should be
visible below the workpiece.
u
Never hold the workpiece in your hands or across your
leg while cutting. Secure the workpiece to a stable
platform.
It is important to support the work properly to
minimise body exposure, blade binding, or loss of con-
trol.
u
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting tool
may contact hidden wiring or its own cord.
Contact
with a "live" wire will also make exposed metal parts of the
power tool "live" and could give the operator an electric
shock.
u
When ripping always use a rip fence or straight edge
guide.
This improves the accuracy of cut and reduces the
chance of blade binding.
u
Always use blades with correct size and shape (dia-
mond versus round) of arbour holes.
Blades that do not
match the mounting hardware of the saw will run off-
centre, causing loss of control.
u
Never use damaged or incorrect blade washers or
bolt.
The blade washers and bolt were specially designed
for your saw, for optimum performance and safety of op-
eration.
Kickback causes and related warnings
- kickback is a sudden reaction to a pinched, jammed or mis-
aligned saw blade, causing an uncontrolled saw to lift up and
out of the workpiece toward the operator;
- when the blade is pinched or jammed tightly by the kerf
closing down, the blade stalls and the motor reaction drives
the unit rapidly back toward the operator;
- if the blade becomes twisted or misaligned in the cut, the
teeth at the back edge of the blade can dig into the top sur-
face of the wood causing the blade to climb out of the kerf
and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect operat-
ing procedures or conditions and can be avoided by taking
proper precautions as given below.
u
Maintain a firm grip on the saw and position your arms
to resist kickback forces. Position your body to either
side of the blade, but not in line with the blade.
Kick-
back could cause the saw to jump backwards, but kick-
back forces can be controlled by the operator, if proper
precautions are taken.
u
When blade is binding, or when interrupting a cut for
any reason, release the trigger and hold the saw mo-
tionless in the material until the blade comes to a com-
plete stop. Never attempt to remove the saw from the
work or pull the saw backward while the blade is in
motion or kickback may occur.
Investigate and take cor-
rective actions to eliminate the cause of blade binding.
u
When restarting a saw in the workpiece, centre the
saw blade in the kerf so that the saw teeth are not en-
gaged into the material.
If a saw blade binds, it may walk
up or kickback from the workpiece as the saw is restar-
ted.
u
Support large panels to minimise the risk of blade
pinching and kickback.
Large panels tend to sag under
their own weight. Supports must be placed under the
panel on both sides, near the line of cut and near the edge
of the panel.
1 609 92A 66T | (22.12.2020) Bosch Power Tools