Bosch PCM 8 SD, Инструкция по эксплуатации

Страница: 32 / 329

32 | English
– Now push the tool arm towards the fences (9) and (11)
and saw through the workpiece with uniform feed.
– Switch off the power tool and wait until the saw blade has
come to a complete stop.
– Slowly guide the tool arm upwards.
Adjusting the depth stop (sawing the groove) (see figure
O)
The depth stop needs to be adjusted if you wish to saw a
groove.
– Swivel the depth stop
(34) outwards.
– Swing the tool arm downward by the handle (6) until the
cutting depth indicator (36) displays the required cutting
depth on the cutting depth scale (35) .
– Turn the adjusting screw (33) until the end of the screw
touches the depth stop (34) .
– Slowly guide the tool arm upwards.
Sawing workpieces of the same length (see figure P)
The length stop (10) (accessory) can be used for easily saw-
ing workpieces to the same length.
– Loosen the clamping lever
(50) and set the length stop
(10) to the required workpiece length.
– Retighten the clamping lever (50) .
Replacing insert plates (see figure Q)
The black insert plate (16) can become worn after pro-
longed use of the power tool.
Replace a defective insert plate.
– Bring the power tool into the work position.
– Unscrew the fastening screw
(66) using the hex key (49)
and remove the old insert plate.
– Insert the new insert plate and screw the fastening screw
(66) in tight again.
Working on mouldings
Mouldings can be sawn in two different ways:
Positioning of
workpiece Base moulding Crown moulding
– Placed against
the fence
– Lying flat on the
saw table
Furthermore, you can cut with or without the slide move-
ment depending on the width of the moulding.
Always check the set mitre and/or bevel angle first by mak-
ing trial cuts in scrap wood.
Transport (see figure R)
Before transporting the power tool, the following steps must
be carried out:
– Bring the power tool into the transport position.
– Insert the flexible saw table extensions (63) into the
openings (64) of the power tool.
– Remove all accessories that cannot be securely fitted to
the power tool.
If possible, transport unused saw blades in an enclosed
container.
– Carry the power tool by the transport handle (2) .
u
Only use the transport devices to transport the power
tool and never the protective devices.
Maintenance and servicing
Maintenance and cleaning
u
Pull the plug out of the socket before carrying out any
work on the power tool.
u
To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by
Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
The retracting blade guard must always be able to move
freely and retract automatically. It is therefore important to
keep the area around the retracting blade guard clean at all
times.
Always remove dust and chips after working by blowing out
with compressed air or using a brush.
Clean the guide roller
(24) regularly.
Accessories
Article number
Saw blades for wood
216 x 30 mm saw blade, 24 teeth 2 608 640 431
216 x 30 mm saw blade, 48 teeth 2 608 640 432
Saw blades for hardwood and composites
216 x 30 mm saw blade, 60 teeth 2 608 640 433
After-sales service and advice on using products
Our after-sales service can answer questions concerning
product maintenance and repair, as well as spare parts. You
can find exploded drawings and information on spare parts
at:
www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the type plate of
the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
1 609 92A 4M8 | (04.12.2018) Bosch Power Tools