28
en
Troubleshooting
Prerinse all other parts under running water.
Clean parts with a brush.
Cleaning the blender
The blender jug (without the blade insert),
lid and funnel are dishwasher-proof. Do not
clean the blade insert in the dishwasher but
under running water (do not soak in water).
Taking the blade insert apart for cleaning
X
Fig.
N
1.
Turn the empty blender jug over. Rotate
the blade insert anti-clockwise by the
wings. The blade insert will release.
2.
Take the blade insert out and remove
the sealing ring.
3.
After cleaning and drying, fit the sealing
ring to the blade insert.
4.
Fit the blade insert into the blender
jug from below and rotate clockwise to
secure.
Rotate the blade insert at least until the
wing matches up with the marking on
the blender jug.
Caution!
Never use the blade insert without the seal.
Cleaning the universal cutter
It is recommended cleaning the universal
cutter immediately after use. This will
prevent residues from drying on and
possibly attacking the plastic (e.g. essential
oils in herbs).
Do not clean the jug with the drive in the
dishwasher but under running water using
a brush. Do not leave in water. To dry, place
the jug with the drive facing up.
Troubleshooting
W
Risk of injury!
Before dealing with any faults, disconnect
the mains plug.
Important information:
The illuminated ring (operation indicator)
will flash if there is an error in operation,
the electronic fuses have tripped or the
appliance has a defect.
Fault:
Appliance is no longer working.
Possible cause:
The appliance has been overloaded
(e.g. tool jammed by food) and the
electronic fuse has tripped.
Remedial action:
■
Set rotary switch to
P
.
■
Disconnect the mains plug.
■
Eliminate the cause of the overload.
■
Switch the appliance back on again.
Possible cause:
An attempt was made to attach the bowl or
blender to the appliance while switched on.
Remedial action:
■
Set rotary switch to
P
.
■
Disconnect the mains plug.
■
Attach the bowl or blender.
■
Switch the appliance back on again.
Fault:
Appliance does not start.
Possible cause:
Parts not correctly attached. Lid not closed
completely.
Remedial action:
■
Set rotary switch to
P
.
■
Disconnect the mains plug.
■
Attach parts correctly according to the
instructions and close the lid completely.
■
Switch the appliance back on again.
Important information:
If the fault cannot be eliminated, please
contact customer service (see customer
service addresses at the end of this
booklet).
Содержание MultiTalent 8 MC812 Series
