Bosch MIC-7502-Z30B Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 47

Bosch MIC-7502-Z30B Скачать руководство пользователя страница 23

MIC IP starlight 7000i

Mounting | en

23

Bosch Security Systems

Installation Manual

2017.09 | 0.12 | F.01U.xxx.xxx

Figure 7.8: Do NOT allow screws or other objects to fall inside camera!

!

Warning!

Risk of bodily injury.
Do not stand the canted (45°) MIC camera upright on the camera base or on an unsecured
DCA, with the DCA base upright! It is unstable and might fall and cause bodily injury and/or
damage to the camera. Bosch strongly recommends canting the camera after attaching it to a
DCA and mounting it in the desired location.

Notice!

If your MIC camera will be canted, install the sunshield first.
If your MIC camera will have both illuminator and sunshield accessories, install the illuminator
first.

To cant the camera, follow these steps:
1. Remove the yoke cap (item 3 in the figure below) on one yoke arm of the camera, using the
supplied spanner wrench (item 2).
Repeat for the second arm.

Figure 7.9: Remove yoke caps with spanner tool

2. Remove the two (2) screws at the bottom of one yoke arm using a wrench (user-supplied)
as described below.

«
...
21
22
23
24
25
...
»

Содержание MIC-7502-Z30B
















































Отзывы:

Нет отзывов