Bosch MIC-7502-Z30B Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 47

Bosch MIC-7502-Z30B Скачать руководство пользователя страница 14

14

en | Configuration Programming in the Shipping Box

MIC IP starlight 7000i

2017.09 | 0.12 | F.01U.xxx.xxx

Installation Manual

Bosch Security Systems

5

Configuration Programming in the Shipping Box

The camera packaging allows installers to connect the camera to the network and configure
the camera still in the box.
1. Remove the accessories box from the top, middle section of the box.

2. Supply power to the camera and

Connect the Camera to the Network, page 29

. Note that

the wiper moves one to three times across the camera window, and then returns to parked
position.
3. Configure the camera. Refer to Configuration for details.

!

Caution!

Risk of damage to camera
Do not change the camera orientation to “Inverted” while the camera is still in the box. The
camera head must be free to rotate. If you must change the camera’s orientation to
“Inverted,” remove the camera from the box and configure it by following the steps in

Configuration Programming on a Temporary Table-top Stand, page 15

.

4. Disconnect the wires/cables from the connectors in the base of the camera.

«
...
12
13
14
15
16
...
»

Содержание MIC-7502-Z30B
















































Отзывы:

Нет отзывов