Bosch LTC 8900 Series, Руководство пользователя

Страница: 21 / 36

EN
| 21
LTC 8900 | User Manual | Keyboard User Functions
Bosch Security Systems | March 17, 2009
6.1.35 User Function 34 -
Camera Indicator
Priority 1 users can use this function to enable an on-
screen indicator to identify a pan/tilt equipped camera.
Move the joystick up/down to select
DISP CAM
CONTROL or NO CAM CONTL DISPL . Press
ENTER to activate your selection. When enabled,
cameras identified as controllable (via User Function 35
or the PC software package), show a

in the middle
of the first line of monitor text.
6.1.36 User Function 35 -
Controllable Cameras
Priority 1 users can use this function to select camera
sites equipped with pan/tilt devices. Move the joystick
up/down to select the camera number, and left/right to
select
FIXED or MOVABLE .
User Function 34
or the
optional PC software package enables or disables the
display of the controllable camera indicators on the
system monitor displays.
6.1.37 User Function 36 -
Select Crosspoint Data
Priority 1 users can use this function to select options
for accessory device data that can be sent out the
biphase control port. Move the joystick up/down to
select
XPOINT DATA , ALARM XPOINT , or
PHYSICAL CAMERA NUMBER , and left/right to
enable/disable the selected option. These options need
only be enabled when Switcher Follower accessory
devices are used in the system.
6.1.38 User Function 37 -
R/D Address Mode
Priority 1 users can use this function to select whether
the biphase control data commands will be addressed
using the cameras
logical numbers or physical indexes
in the camera table. Move the joystick up/down to
select
LOGICAL or PHYSICAL and press ENTER to
activate your selection. If this option is set to
LOGICAL , receiver/drivers should be addressed
using the cameras logical identification number. If
it is set to
PHYSICAL , receiver/drivers should be
addressed using the cameras physical number.
6.1.39 User Function 38 -
Console Port Mode
This function allows configuration of the system s console
port, for use with a Console Port Expander accessory
device. Priority 1 users can move the joystick up/down to
select the console port function; NORMAL or
EXPANDED. Press
ENTER to activate your selection.
You must reset the system for this setting to take effect.
6.1.40 User Function 39
Select DIU Interface Port
Priority 1 users can use this function to select the
switcher s interface port to be connected to an external
Allegiant Bilinx
TM
Data Interface accessory unit. Move
the joystick up/down until the desired port for use as a
data interface (DIU) is displayed. Press
ENTER to
configure the port. If using the LTC 8555 keyboard,
press
USER to exit the mode.
6.1.41 User Function 40 -
Reserved Function
6.1.42 User Function 41
Set Satellite Communication Format
This function provides three (3) configuration options
that determine the behavior and content of the data
commands issued by a master system to a satellite
system. In most cases, it is only necessary to change
the default setting if using a multi-level cascaded
Allegiant satellite system configuration. (Refer to
Appendix section for more information on Satellite
system configurations.) Detailed descriptions of these
options are listed below.
After entering the mode, move the joystick up or down
to select the desired option. Enter a valid user
password, and press [Enter].
a) "CACHE REM CAM" option (default factory
setting). In this mode, satellite commands are issued
repetitively, regardless of whether the satellite camera
is still being viewed by an operator. This mode of
operation is more desirable in standard systems
because it minimizes delays when previous Satellite
cameras are reselected. It is not recommended for use
in cascaded systems. In cascaded systems, this mode
could result in all available Trunk Lines coming from
the 3rd level satellite system to become used up,
making them unavailable to the operators at the
intermediate system.
b) "NO REM CAM CACHE" option. In this mode,
after the top level operator selects a locally connected
camera, the Trunk Line between the top level and the
intermediate level system will immediately be reset to
its Start-up camera (as defined in the Monitor table of
the LTC 8059/00 Master Control Software). This in
turn frees up the Trunk Line between the intermediate
level system and the 3rd level system so it will be
available if needed by an operator at the intermediate
level system.