Bosch LSN Скачать руководство пользователя

Страница: 20 / 32

PI - 32.15a

Product Documentation of the LSN Radio Fire Detection System

Seite 20 von 32

601-F.01U.002.708

A3.en / 28.12.2004

ST-FIR/ PRM1 / deh

6.5. Expanding a radio cell (adding RF detectors)

Call up the “Enter as” menu in WinPara under
“System”

⇒

“Peripheral control”

⇒

“LSN”

⇒

“FK100”

⇒

“LSN”.

Enter the number of new DOW1171s.

Load programming in the fire panel.

Activate expansion under “FK100” via
“DOW1171 to be added”.

⇒

The green LED on FK 100 LSN flashes rapidly, indicating that detectors can now
be added.

Log RF detector on to RF expansion module:

Insert the batteries and secure the cables,
as shown in the diagram on the right.

⇒

The LED must flash slowly.

If the LED flashes rapidly, press the new button and
hold it for at least 3 sec.

⇒

The detector will be reset to its default settings and
the red LED will flash slowly.

Insert the detector in the base

within 10 minutes of

inserting the batteries

⇒

Following a successful system logon (duration:
15 sec. to a max. of 10 mins), the red LED will go
out and then flashes again for two minutes to in-
dicate the field strength.

Flashes/sec.

Field strength

Effect

High

Within field strength range adequate for de-

Moderate

Within field strength range adequate for de

tector use!

Low

Impermissible field strength range!

Very low

Impermissible field strength range!

Improve detector positioning!

⇒

The yellow LED lights up briefly to acknowledge
each successful logon.

All other RF detectors (maximum of 30) are logged
on in this way one after the other.

⇒

Once the last DOW 1171 has been logged on,
FK 100 LSN starts system configuration and the
green LED flashes slowly.

⇒

Following successful system configuration, the green LED lights up permanently,
indicating that the radio cell is in standard mode.

Button new

LED

red

LED yellow

LED green

Содержание LSN
































Результаты поиска

Содержание LSN

Отзывы:

Похожие инструкции для LSN

Бренды по названию

Популярные бренды

Bosch LSN, Продуктовая документация

Результаты поиска

Содержание LSN

Отзывы:

Похожие инструкции для LSN

Бренды по названию

Популярные бренды