Bosch LSN Скачать руководство пользователя страница 16

Страница: 16 / 32

PI - 32.15a

Product Documentation of the LSN Radio Fire Detection System

Seite 16 von 32

601-F.01U.002.708

A3.en / 28.12.2004

ST-FIR/ PRM1 / deh

Initial Set - Up with Fire Panel and WinPara

Connect the LSN and supply voltage to RF expan-
sion module FK 100 LSN.

⇒

The red LED on FK 100 LSN lights up for a few sec-
onds, after which the yellow LED flashes slowly to
indicate that FK 100 LSN is in standby mode.

Programm the entire system including
FK 100 LSN on the programming PC using Win-
Para and load all RF detectors to be set in the fire
panel.

Activate the menu item “Reset FK100” in WinPara
under FK 100 LSN.

⇒

The red LED on FK 100 LSN lights up briefly, then
the green and yellow LEDs start to flash rapidly to
indicate a frequency search (max. 10 min.).

⇒

Following a successful frequency search, the yel-
low LED goes out to indicate that it is now possible
to log on to the RF detector.

Log RF detector on to RF expansion module:

Insert the batteries and secure the cables,
as shown in the diagram on the right.

⇒

The LED on the detector should flash slowly.

If the LED is flashing rapidly, press the new button
and hold it for at least 3 seconds.

⇒

The detector will be reset to its default settings and
the red LED will flash slowly.

Insert the detector in the base

within 10 minutes of

inserting the batteries

⇒

Following a successful system logon (duration:
15 sec. to a max. of 10 mins), the red LED will go
out and then flashes again for two minutes to indi-
cate the field strength.

Flashes/sec.

Field strength

Effect

High

Within field strength range adequate for

Moderate

Within field strength range adequate for

detector use!

Low

Impermissible field strength range!

Very low

Impermissible field strength range!

Improve detector positioning!

LED green

LED yellow

LED red

Button new

LED

red

Содержание LSN
































Результаты поиска

Содержание LSN

Отзывы:

Бренды по названию

Популярные бренды

Bosch LSN, Продуктовая документация

Результаты поиска

Содержание LSN

Отзывы:

Бренды по названию

Популярные бренды