ICP-CC404
|
Installation Guide | 16.0 Programmable Outputs
64 Bosch
Security
Systems,
Inc. | 12/08 | F01U089401-02
Table 50:
Test Reporting Time Parameters
Location Parameter
Default
360
Hour of day (tens digit)
0
361
Hour of day (units digit)
0
362
Minute of day (tens digit)
0
363
Minute of day (units digit)
0
364
Test Report (tens digit)
7
365
Test Report (units digit)
1
366
Repeat interval in days
0
A Test Report (Contact ID Event Code 602) is a
specific signal sent to the base station receiver and is
normally used to test the dailing and reporting
functions of the control panel.
When programming Test Report options, specify the
hour and minute of the day the report is required,
and how often to send the report. Test reports are
sent on a daily basis from every day to every fifteen
days. Refer to
Section 6.1.1 Set the Number of Days until
the First Test Report
on page 27 to set the first test
report.
If Test Reports are not required, program
the repeat interval in Location 366 as 0.
Program the Test Report Time as 24:00
to send reports every 30 min.
Example
To send Test Reports once every seven days at 11:35
PM, program Locations 360 to 366 as:
2 3 3 5 7 1 7
15.22 Test Reporting Dialer Options
Use
Location 367
to select whether Test Reports are
sent to Receiver 1 (the default), Receiver 2, or both,
Receiver 2 only when Receiver 1 fails, or there is no
reporting at all.
Table 51
lists the reporting options.
Table 51:
Test Reporting Options
Option Description
0
No Test Reports required
1 Receiver
1
2
Receiver 2
4
Receiver 1 and Receiver 2
8
Receiver 2 only when Receiver 1 fails
16.0 Programmable Outputs
The ICP-CC404 Control Panel has four fully-
programmable outputs on the main printed circuit
board and one programmable output that operates
the codepad buzzer. The four outputs are set by
default to operate as horn speaker, fire alarm
verification, strobe, and internal screamer.
Outputs 1 to 4 do not operate when the
control panel detects a low battery.
Programmable outputs require four parameters to
operate correctly.
Table 52:
Output Parameters
Parameter Description
Event Type
The Event Type specifies when an output
is activated. The Output Event Types are
listed in
Section 16.2
. Enter the code for
the Output Event Type into the two
corresponding locations for the output.
Polarity Polarity
determines whether the output
operates for the duration of the event,
pulses for the duration, operates once only
(one shot), or latches on. The polarity
options are listed in
Table 54
on page 69.
Time Base/
Time
Multiplier
The Time Base and Time Multiplier
parameters determine how long and how
often the output operates. Refer to
Section
16.4 Output Timing
on page 70.
Table 53:
Output Programming Defaults
Output
Default Output Type
Locations
Event Code
Polarity
Time Base
Time Base Multiplier
Output 1
Horn Speaker
368 to 373
1
14
0
0
0
0
Output 2
Fire Alarm with Verification 374 to 379
2
7
10
2
1
5
Strobe
Strobe – Reset in 8 hr
380 to 385
2
0
6
4
0
8
Relay
Sirens Running
386 to 391
1
15
1
0
0
0
Codepad
Buzzer
Entry/Exit Warning and
Day Alarm
392 to 397
0
13
2
1
0
1
16.1 Redirecting Outputs to the Codepad
Buzzer
Multiple output event types can be directed to the
codepad buzzer so the buzzer can indicate a number
of events.
To redirect an output to the codepad buzzer, select an
output and program it for the desired Output Event
Type. If the output is functioning correctly, add 8 to
the first (tens) digit of the Output Event Type.
