en
Installation and connection
10
5
Installation and connection
Installation and connection
Do not install the appliance behind a decorative door
or the door of a kitchen unit, as this may cause the
appliance to overheat.
Gas connection
Installation must only be performed by an approved
expert or a licensed after-sales service engineer in
accordance with the instructions specified under "Gas
connection and conversion to a different gas type".
For the licensed expert or after-sales service
Caution!
■
The setting conditions for this appliance are
specified on the rating plate on the back of the
appliance. The gas type set in the factory is marked
with an asterisk (*).
■
Before setting up the appliance, check the grid
access conditions (gas type and gas pressure) and
ensure that the gas setting of the appliance meets
these conditions. If the appliance settings have to be
changed, follow the instructions in the section "Gas
connection and conversion to a different gas type".
■
This appliance is not connected to a waste gas
main. It must be connected and commissioned in
accordance with the installation conditions. Do not
connect the appliance to a waste gas main. All
ventilation regulations must be observed.
■
The gas connection must be made via a fixed, i.e.
not mobile connection (gas line) or via a safety
hose.
■
If using the safety hose, ensure that the hose is not
trapped or crushed. The hose must not come into
contact with hot surfaces.
■
* The gas line (gas pipe or gas safety hose) can be
connected to the right- or left-hand side of the
appliance. The connection must have an easily
accessible shut-off device.
* Optional. Available for some appliances.
Target appliance operating pressure
Your appliance's target operating pressure is specified
on the rating plate on the back of the appliance.
All the data on your appliance's rating plate relates to
these pressure values. The manufacturer shall not be
held liable for results, performance or any risk caused
by operating the appliance at pressure values other
than those specified.
:
Warning – Safety information!
If the gas pressure in your distributing pipes is higher
(20%) than the values specified on the appliance's
rating plate, it is important that you operate the
appliance with a suitable gas regulator for your safety.
If you do not know what the gas pressure in your
distributing pipes is, contact your local gas company.
The gas regulator must be connected, maintained and
adjusted by specialists from your local gas company.
Faults in the gas installation/smell of gas
If you notice a smell of gas or faults in the gas
installation, you must
■
immediately shut off the gas supply and/or close the
gas cylinder valve
■
immediately extinguish all naked flames and
cigarettes
■
switch off electrical appliances and lights
■
open windows and ventilate the room
■
call the after
sales service or the gas supplier
Moving the appliance by the gas line or door handle
Do not move the appliance while holding the gas line;
the gas pipe could be damaged. There is a risk of a gas
leak! Do not move the appliance while holding it by the
door handle. The door hinges and door handle could
be damaged.
Electrical connection
The appliance is designed to operate at 220-240 V. A
16 A fuse is required for connection.
Have the appliance installed by your after-sales service.
Any damage arising from the appliance being
connected incorrectly will invalidate the warranty.
Caution!
■
If the electricity supply drops below 180 V, the
electrical ignition system does not work.
■
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
:
Warning – Danger of death!
There is a risk of electric shock if you touch live
components.
■
Always make sure your hands are dry when you
touch or hold the mains plug.
■
Only pull out the mains cable by taking hold of the
plug and removing the plug; never pull it out by the
mains cable itself, as this could damage it.
■
Never unplug the mains plug when the appliance is
in operation.
Please note the following information and ensure that:
Notes
■
The mains plug fits the socket.
■
The cable cross section is adequate.
■
The earthing system is properly installed.
■
The mains cable is only replaced by a qualified
electrician (if this is necessary).Spare mains cables
can be ordered from our after-sales service.
■
No power strips/multi-way connectors or extension
cables are used.
■
If using a residual current device, only use one that
bears the mark
z
.
The presence of this mark is the only way to be sure
that it fulfils all the applicable regulations.
■
The mains plug can be accessed at all times.
■
The mains cable is not kinked, crushed, modified or
severed.
■
The mains cable does not come into contact with
heat sources.
