Bosch GV 630 S Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 56

background image

5 FUNCTIONS

5.1

3 in 1 detergent detection function

The rinse aid temperature is increased by 3 K for the 3 in 1 detergent
detection function (as for intensive drying). This improves the drying
result.
The 3 in 1 detergent detection function is activated if:

►

►

the electronics detect low rinse aid
the

rinse-aid refill indicator is deactivated

The "Intensive drying" additional function can still be selected, but it
has no effect on the rinse-aid temperature.
The maximum temperature increase is 3 K.

202_58300000104305_ara_en_b – 02.11.a

Seite 40 von 56

«
...
38
39
40
41
42
...
»

Содержание GV 630 S

























































Отзывы:

Нет отзывов

Похожие инструкции для GV 630 S

Бренд: Samsung Страницы: 36

Бренд: Cookology Страницы: 24

Computer Control 1100 A3268

Бренд: Hoover Страницы: 12

Бренд: Proline Страницы: 18

Conservator 3955874A

Бренд: Crosley Страницы: 8

Бренд: Vivax Страницы: 59

Бренд: iLive Страницы: 53

Бренд: Smeg Страницы: 27

Aqualtis AQXXL 149 PI

Бренд: Hotpoint Страницы: 16

Бренд: Progress Страницы: 56

Бренд: Salora Страницы: 77

DishDrawer DD24D Series

Бренд: Fisher & Paykel Страницы: 8

Бренд: Electrolux Страницы: 19

Бренд: Electrolux Страницы: 28

Бренд: Electrolux Страницы: 12

Бренд: Electrolux Страницы: 12

Бренд: Electrolux Страницы: 40

Бренд: Electrolux Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды