manualshive.com logo in svg

Bosch Greentherm T9800 SEO160, Инструкция по установке и эксплуатации

Поделиться
Скачать
Bosch Greentherm T9800 SEO160 Скачать руководство пользователя страница 8

Appliance details

 

Greentherm T9800 SEO 160/199 | SECO 199 – 6 720 817 281 (2018/12)

8

Table 2  

Approximate time-temperature relationship until 
there is a risk of scalding

WARNING: 

This product can expose you to chemicals including lead, which 
is know to the State of California to cause cancer and birth 
defects or other reproductive harm. For more information go to 
www.P65Warnings.ca.gov.

BOSCH water heater complies with the State of California Lead 
Law (AB1953).

3

Appliance details

3.1

Features

Residential
•

Greentherm T9800 SEO residential models
– maximum temperature 120 °F (49 °C)

1)

Parts
•

High power segmented burner with low NOx emissions.

•

Modulating gas valve.

•

Modulating water valve.

•

Active bypass water valve for quick response to changing 
water flows.

•

Burner power segmentation with modulation range from 
1:22.

High quality materials for long working life
•

Copper heat exchanger.

•

Stainless Steel 316L condensing heat exchanger

Features
•

Compact space saver: mounts on a wall with a supplied 
bracket.

•

Easy minimum to achieve low output power.

•

Easily removable one-piece cover.

•

On/Off and Temperature remote control.

•

Program button (Selectable temperature default).

•

Failure codes for easy diagnostics and repair.

•

Real-time diagnostics for troubleshooting/informational 
purposes.

•

Built in freeze protection.

•

Integrated siphon to limit condensate freezing in external 
condensate pipes.

Note: The freeze prevention kit is designed to provide 
protection for the water heater down to 

approximately -4 °F 

(-20 °C) for short term conditions only when protected 
from direct wind exposure

. It will not protect the appliance in 

areas where the temperature is routinely expected to be below 
freezing. Drain the water heater in the event of power outage in 
freezing conditions.
- The freeze prevention kit will not protect plumbing outside the 
appliance from freezing. Precautions should be taken.

Accessories (Bosch part #)
•

Neutralizer Kit (7738001483)

•

Aquastat kit (7736504584)

•

Recirculation pump kit (7736504585)

•

Tank loading NTC (7736504583)

•

Wired remote control (7736504946)

•

Wired remote control with WiFi (7736504945)

BOSCH is constantly improving its products, therefore 
specifications are subject to change without prior notice.

1) Source: Moritz, A.R. and Henriques, F.C., Jr. (1947). 

Studies of thermal injury. II. The relative importance of 
time and surface temperature in the causation of 
cutaneous burns, Am J of Pathol, 23, 695-720.

1) Can be programmed to achieve 140 °F (60 °C)

Содержание Greentherm T9800 SEO160

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды