Bosch Greentherm T9800 SEO160 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 56

background image

Operating Instructions

27

Greentherm T9800 SEO 160/199 | SECO 199 – 6 720 817 281 (2018/12)

6

Operating Instructions

Fig. 25

Digital display

[1]

On/Off button

[2]

Programming button

[3]

LCD display

[4]

Increase / Enter button

[5]

Decrease / Return button

NOTICE:

▶ Wipe down with a damp cloth. Do not use any aggressive or

corrosive cleaning agents to clean the window.

Fig. 26

Description LCD display

[1]

Locked condition indicator

[2]

Error indicator

[3]

Temperature indicator

[4]

Activation water flow

[5]

Cascading Master indicator

[6]

Solar mode indicator

[7]

Flame indicator

[8]

Power bar indicator

6.1

For your safety read before operating your
water heater

WARNING:

Explosion hazard!

▶ If you do not follow these instructions exactly, a fire or

explosion may result causing property damage, personal
injury or loss of life.

NOTICE:

Appliance malfunction!

Strong magnetic fields can interfere with the electronics, which
can lead to appliance malfunction.
▶ Do not attach magnets to this water heater, do not install

near strong magnetic fields.

A.

This appliance is equipped with electronic ignition for

lighting the main burner. When turning the heater on, follow
these instructions exactly.

WHAT TO DO IF YOU SMELL GAS

▶ Turn off the gas shut-off valve.
▶ Open windows and door if smell detected inside the house.
▶ Do not try to ignite the appliance.
▶ Do not touch any electrical switch, telephone, and do not

use outlets.

▶ Extinguish all open flames. Do not smoke! Do not use

lighters!

▶ Warn all occupants of the building. Do not ring doorbells!
▶ If you can hear gas leaking, leave the building immediately.
▶ Prevent others from entering the building and notify the

police and fire department from outside the building.

▶ From outside the building, call the gas utility company and

a trained and certified installer.

B.

Never use tools, close the gas supply and call a qualified

service technician. Forceful repair may result in a fire or
explosion.

C.

Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and any
gas control which has been under water.

6.2

Power

To turn ON the appliance:

To access appliance HMI, procedure as follows:
▶ Remove front cover, see fig. 3.
▶ Press the button

.

The display shows the desired water temperature.

6720806146-02.1V

1

2

5

3

4

8

1

2
3

4

5

6

7

6720817

9

84-51

.

1V

«
...
25
26
27
28
29
...
»

Содержание Greentherm T9800 SEO160

























































Отзывы:

Нет отзывов

Похожие инструкции для Greentherm T9800 SEO160

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

Бренд: Danfoss Страницы: 16

Бренд: Watson-Marlow Страницы: 128

Бренд: BLACKMER Страницы: 12

FLORES C CH E - MOUNTING

Бренд: RADSON Страницы: 4

PTH38PSS, PTH38PCP, PTH38PGM

Бренд: Napoleon Страницы: 15

Бренд: Protemp Страницы: 30

Бренд: Mr. Heater Страницы: 36

Fre-Heater D Series

Бренд: Mueller Страницы: 34

HOTSPRING HSTB9

Бренд: ZANSKAR Страницы: 19

Бренд: salmson Страницы: 28

DULCO Trans 40/1000 PVDF

Бренд: ProMinent Страницы: 52

Бренд: Eckerle Страницы: 6

Бренд: REMKO Страницы: 16

Бренд: Trotec Страницы: 18

Бренд: Twin-Star International Страницы: 18

Бренд: Dometic Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды