Bosch Greentherm T9800 SEO160 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 56

background image

Safety information

7

Greentherm T9800 SEO 160/199 | SECO 199 – 6 720 817 281 (2018/12)

H

WARNING:

Relief valve discharge

▶ If a relief valve discharges

periodically, this may be due to
thermal expansion in a closed water
supply system. Contact the water
supplier or local plumbing inspector
on how to correct this situation. Do
not plug the relief valve.

H

WARNING:

Personal Injury from toxic chemicals.

▶ Toxic chemicals, such as those used

for boiler treatment, shall not be
introduced into the potable water
used for space heating.

H

WARNING:

Personal Injury from toxic chemicals.

▶ A water heater which will be used to

supply potable water shall not be
connected to any heating system or
component(s) previously used with a
nonpotable water heating appliance.

2

Safety information

Fig. 1

The chart below shows the relationship between water
temperature and time until there is a risk of scalding. It can be
used as the basis for determining the safest water temperature
for your application.

Temperature

Time to severe scalding

1)

120 °F (48 °C)

longer than 5 minutes

125 °F (51 °C)

1.5 to 2 minutes

130 °F (54 °C)

approx. 30 seconds

135 °F (57 °C)

approx. 10 seconds

140 °F (60 °C)

less than 5 seconds

145 °F (62 °C)

less than 3 seconds

150 °F (65 °C)

approx. 1.5 seconds

155 °F (68 °C)

approx. 1 second

«
...
5
6
7
8
9
...
»

Содержание Greentherm T9800 SEO160

























































Отзывы:

Нет отзывов

Похожие инструкции для Greentherm T9800 SEO160

Бренд: Lasko Страницы: 4

Бренд: Macnaught Страницы: 12

Бренд: A.O. Smith Страницы: 2

Бренд: WaterCare Страницы: 7

JABSCO 11860 Series

Бренд: Xylem Страницы: 24

Бренд: GE Страницы: 12

Бренд: Gude Страницы: 62

Бренд: UNITED Страницы: 8

Бренд: DAXOM Страницы: 20

Бренд: Danner Страницы: 2

Бренд: veito Страницы: 24

Бренд: Vasco Страницы: 32

Бренд: EBARA Страницы: 69

Бренд: Graco Страницы: 28

Бренд: Aktobis Страницы: 5

Бренд: Wacker Neuson Страницы: 68

Бренд: N'oveen Страницы: 15

Бренд: L.B. White Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды