12
| English
1 609 92A 3PM | (22.12.16)
Bosch Power Tools
– Switch the machine off and wait until the cutting disc
comes to a complete stop.
– Guide the tool arm slowly upward.
Adjusting the Depth Stop (see figure H)
In the delivery condition of the machine, the depth stop
17
is
adjusted in such a manner that a new 355 mm cutting disc
does not touch the base plate when cutting.
To compensate the wear of the cutting disc, the depth stop
can be set deeper.
When using a new cutting disc, the depth stop must then al-
ways be set back to the original position.
Always adjust the depth stop in such a manner that the
cutting disc does not touch the base plate when cut-
ting.
– Bring the power tool into the working position. (see “Re-
leasing the Machine (Working Position) (see figure C1)”,
page 10)
– Loosen lock nut
26
with the supplied ring spanner
14
(13 mm).
– Swing the tool arm with the handle
3
to the requested po-
sition.
– Screw the depth stop
17
in clockwise or anticlockwise di-
rection until the screw head touches the housing.
– Slowly guide the tool arm upward and tighten the lock nut
26
.
Transport
– Always carry the power tool by its transport handle
18
.
When transporting the power tool, use only the trans-
port devices and never use the protective devices.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
plug.
Clean the ventilation slots of your power tool regularly
with a soft brush.
The motor fan draws dust into the hous-
ing, and a large accumulation of metal dust can lead to
electrical hazards.
In extreme conditions, always use dust extraction as
far as possible. Blow out ventilation slots frequently
and install a portable residual current device (PRCD).
When working metals, conductive dust can settle in the in-
terior of the power tool. The total insulation of the power
tool can be impaired.
Have maintenance and repair work performed only by
qualified specialists.
In this manner, it can be ensured
that the safety of the power tool is maintained.
The retracting blade guard must always be able to move freely
and retract automatically. Therefore, always keep the area
around the retracting blade guard clean.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Accessories
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch’s application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
People’s Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 4008268484
Fax: (0571) 87774502
E-Mail: [email protected]
www.bosch-pt.com.cn
HK and Macau Special Administrative Regions
Robert Bosch Hong Kong Co. Ltd.
21st Floor, 625 King’s Road
North Point, Hong Kong
Customer Service Hotline: +852 2101 0235
Fax: +852 2590 9762
E-Mail: [email protected]
www.bosch-pt.com.hk
Indonesia
PT Robert Bosch
Palma Tower 10
th
Floor
Jl. RA Kartini II-S Kaveling 6 Sek II
Pondok Pinang, Kebayoran Lama
Jakarta Selatan 12310
Indonesia
Tel.: (021) 3005 5800
Fax: (021) 3005 5801
E-Mail: [email protected]
www.bosch-pt.co.id
Philippines
Robert Bosch, Inc.
28th Floor Fort Legend Towers,
3rd Avenue corner 31st Street,
Fort Bonifacio Global City,
1634 Taguig City, Philippines
Tel.: (02) 8703871
Fax: (02) 8703870
[email protected]
www.bosch-pt.com.ph
Part number
Cutting disc
2 608 600 936
Cutting disc
2 608 602 751
OBJ_BUCH-3091-001.book Page 12 Thursday, December 22, 2016 3:52 PM
