English– 6
1 609 929 E36 • (04.10) PS
4
OPERATING INSTRUCTIONS
Before Use
To ensure safe handling, the feet of the base plate
8
must be placed o n a suitable platfo rm (e.g. wo rk&
bench, even floor, etc.).
Transport Safety
(see Figure
)
Before all work on the machine, pull the mains
plug.
The transport locking pin
24
makes possible easy han&
dling of the machine when transporting to the various
working locations.
Securing the Machine (Transport Position)
Swing the tool arm
13
with the handle
1
downward to
the stop. Swing the transport safety
24
inward until it
rests against the housing and release the tool arm.
Releasing the Machine (Working Position)
Press the tool arm
13
with the handle
1
of the tool arm
downward somewhat to relieve the load on the trans&
port safety. Swing the transport safety
24
outward and
guide the tool arm slowly upward.
Changing the Tool
(see Figure
)
Before all work on the machine, pull the mains
plug.
Use only cutting disks that correspond to the charac&
teristic data given in these operating instructions.
Use only cutting disks whose allowable speed is as
high as the no&load speed of the machine.
Actuate the spindle lock only with the cutting disk is at
a standstill.
Removing the Cutting Disk
Place the machine in the working position.
Hold the cutting disk cover
18
, loosen the screw
22
with a screwdriver and guide the cutting disk co ver
downward.
Turn the hex&head bolt
21
with the open&end spanner
23
(17 mm) provided and press at the same time the
spindle lock
14
until it engages.
Hold the spindle lock depressed and unscrew the hex&
head bolt
21
. Remove the washer
20
and the clamp&
ing flange
19
.
Swing the pendulum protection hood
3
upward to the
stop.
Remove the cutting disk
4
.
Installing the Cutting Disk
If necessary, clean all parts to be mounted.
Swing the pendulum protection hood
3
upward to the
stop. Place the new cutting disk on the tool spindle
17
so that the label points in the direction of the cutting
disk cover
18
.
Place on the clamping flange
19
, the washer
20
and
the hex&head bolt
21
. Press the spindle lock
14
until it
engages and tighten the hex&head bolt
21
with a
torque of approx. 13 Nm.
Guide the pendulum protection hood back down.
Swing the cutting disk cover
18
upward again and
tighten the screw
22
.
Adjusting the Mitre Angle
Before all work on the machine, pull the mains
plug.
The mitre angle can be set in the range from 0° to 45°.
Often used setting values are identified on the angle
stop
9
with appropriate marking. The 0° and 45° posi&
tions are set at the end stops.
Loosen the two angle stop bolts
10
with the open&end
spanner
23
(17 mm) provided. Set the desired angle
and retighten the angle stop bolts.
Clamping the Work Piece
(see Figure
)
Before all work on the machine, pull the mains
plug.
To ensure optimum working safety, the work piece
must always be firmly clamped.
Place the work piece against the angle stop
9
. Slide
the clamping spindle
5
against the wo rk piece and
clamp the work piece firmly with the aid of the crank
7
.
Releasing the Work Piece
Loosen the crank
7
.
Swing up the quick release
6
and pull the clamping
spindle
5
away from the work piece.
Putting into Operation
Switching On and Off
To
switch on
, pull the on/off switch
2
in the direction
of the cutting disk. Then press the on/off switch and
hold it depressed.
For safety reasons, the on/off switch of the ma'
chine cannot be locked on but must remain de'
pressed during operation.
To
switch off
the machine, release the on/off switch
2
.
C
A
B
