English |
25
Bosch Power Tools
1 609 92A 3BW | (6.3.17)
– Adjust the requested mitre and/or bevel angle.
– Press the workpiece firmly against the fences
6
and
21
.
– Firmly clamp the workpiece as appropriate for its dimen-
sions.
– Switch on the machine.
– Press locking switch
17
and slowly guide the tool arm
downward by the handle
16
.
– Saw through the workpiece applying uniform feed.
– Switch off the machine and wait until the saw blade has
come to a complete stop.
– Guide the tool arm slowly upward.
Sawing with Slide Movement
– For cuts using the slide device
12
(wide workpieces), loos-
en the locking screw
11
in case it is tightened.
– Adjust the requested mitre and/or bevel angle.
– Press the workpiece firmly against the fences
6
and
21
.
– Firmly clamp the workpiece as appropriate for its dimen-
sions.
– Pull the tool arm away from the fences
6
and
21
until the
saw blade is in front of the workpiece.
– Switch on the machine.
– Press locking switch
17
and slowly guide the tool arm
downward by the handle
16
.
– Now push the tool arm toward the fences
6
and
21
and saw
through the workpiece with uniform feed.
– Switch off the machine and wait until the saw blade has
come to a complete stop.
– Guide the tool arm slowly upward.
Special Workpieces
When sawing curved or round workpieces, these must be es-
pecially secured against slipping. At the cutting line, no gap
may exist between workpiece, fence and saw table.
Provide for special fixtures, if required.
Checking and Adjusting the Basic Adjustment
Before any work on the machine itself, pull the mains
plug.
To ensure precise cuts, the basic adjustment of the machine
must be checked and adjusted as necessary after intensive
use.
A certain level of experience and appropriate specialty tools
are required for this.
A Bosch after-sales service station will handle this mainte-
nance task quickly and reliably.
Setting the Standard Bevel Angle 0° (Vertical)
– Bring the power tool into the working position.
– Turn the saw table
22
to the 0° detent
28
. The lever
26
must be felt to engage in the detent.
Checking:
(see figure N1)
– Adjust an angle gauge to 90° and position it on the saw ta-
ble
22
.
The leg of the angle gauge must be flush with the saw blade
39
over the complete length.
Adjusting:
(see figure N2)
– Loosen the lock lever
10
.
– Loosen the lock nut of the stop screw
33
using a commer-
cial box-end or open-end spanner (size 10 mm).
– Screw the stop screw in or out until the leg of the angle
gauge is flush with the saw blade over the complete length.
– Retighten the lock lever
10
again.
– Afterwards, retighten the lock nut of the stop screw
33
again.
In case the angle indicator
32
is not in a line with the 0° mark
of the scale
31
after the adjustment, loosen the screw
44
us-
ing a commercial cross-head screwdriver and align the angle
indicator along the 0° mark.
Setting the Standard Bevel Angle 45° (Vertical)
– Bring the power tool into the working position.
– Turn the saw table
22
to the 0° detent
28
. The lever
26
must be felt to engage in the detent.
– Loosen the lock lever
10
and tilt the tool arm leftward to
the stop (45°) by the handle
16
.
Checking:
(see figure O1)
– Adjust an angle gauge to 45° and position it on the saw ta-
ble
22
.
The leg of the angle gauge must be flush with the saw blade
39
over the complete length.
Adjusting:
(see figure O2)
– Loosen the lock lever
10
.
– Loosen the lock nut of the stop screw
9
using a commercial
box-end or open-end spanner (size 10 mm).
– Screw the stop screw in or out until the leg of the angle
gauge is flush with the saw blade over the complete length.
– Retighten the lock lever
10
again.
– Afterwards, retighten the lock nut of the stop screw
9
again.
In case the angle indicator
32
is not in a line with the 45° mark
of the scale
31
, firstly check the 0° setting for the bevel angle
and the angle indicator again. Then repeat the adjustment of
the 45° bevel angle.
Aligning the Angle Indicator (Horizontally) (see figure P)
– Bring the power tool into the working position.
– Turn the saw table
22
to the 0° detent
28
. The lever
26
must be felt to engage in the detent.
Checking:
The angle indicator
24
must be in alignment with the 0° mark
of the scale
5
.
Adjusting:
– Loosen screw
45
using a cross-head screwdriver and align
the angle indicator alongside the 0° mark.
– Retighten the screw again.
Transport (see figure Q)
Before transporting the power tool, the following steps must
be carried out:
– Loosen the locking screw
11
if tightened. Pull the tool arm
completely to the front and tighten the locking screw
again.
– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
OBJ_BUCH-2154-003.book Page 25 Monday, March 6, 2017 11:48 AM
