English |
35
Bosch Power Tools
1 609 92A 285 | (11.11.15)
71
Set screw for 45° basic setting (leftward bevel angle)
72
Set screw for 45° basic setting (rightward bevel angle)
73
Set screws of scale
37
for mitre angles
74
Screw for mitre angle indicator
75
Set screw for clamping force of lock lever
17
76
Velcro strap
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Noise Information
Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 93 dB(A); Sound power level
106 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Assembly
Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material from the machine and the ac-
cessories provided.
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Sliding mitre saw with mounted saw blade
– Locking knob
15
– Dust bag
1
– Hex key
20
– Hex key
21
(below laser protection cap
27
)
– Material clamp
22
Note:
Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Additionally required tools (not in delivery scope):
– Cross-head screwdriver
– Open-end spanner (size: 8 mm)
– Ring, open-end or socket spanner (size: 10 mm and
17 mm)
Mounting the Locking Knob (see figure a)
– Screw the locking knob
15
into the corresponding drill
hole above the lever
16
.
Always tighten the locking knob 15 firmly before saw-
ing.
Otherwise the saw blade can become wedged in the
workpiece.
Stationary or Flexible Mounting
To ensure safe handling, the machine must be mounted
on a level and stable surface (e. g., workbench) prior to
using.
Mounting to a Working Surface (see figure b1)
– Fasten the power tool with suitable screw fasteners to the
working surface. The mounting holes
12
serve for this pur-
pose.
Sliding Mitre Saw
GCM 12 GDL
Article number
3 601 M23 600
3 601 M23 630
3 601 M23 670
3 601 M23 660
3 601 M23 690
3 601 M23 6P0
Rated power input
W
2000
1500
1800
No-load speed
min
-1
3800
3800
3800
Reduced starting current
–
Laser type
nm
mW
635
< 1
635
< 1
635
< 1
Laser class
2
2
2
Weight according to EPTA-Procedure 01:2014
kg
32.1
32.1
32.1
Protection class
/
II
/
II
/
II
Permissible workpiece dimensions (maximum/minimum) see page 39.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
mm
305
Blade body thickness
mm
1.7–2.6
Mounting hole diameter
mm
30
OBJ_BUCH-1360-003.book Page 35 Wednesday, November 11, 2015 2:13 PM
