Bosch GAS 12-25 PL, Оригинальное руководство пользователя

Страница: 22 / 257

22 | English
Cleaning the pre-filter
– Open the catches (9) and remove the top part of the va-
cuum cleaner (10) (see figure C ).
– Remove the pre-filter (22) from the container (7) .
– Shake out the pre-filter (22) over a suitable waste bin.
– Insert the pre-filter (22) in the container (7) , making sure
that the arrows are pointing towards the hose connection
piece
(3) .
– Put the top part of the vacuum cleaner (10) on and close
the catches (9) .
Cleaning the main filter
– Open the catches (9) and remove the top part of the va-
cuum cleaner (10) (see figure C ).
– Turn the filter holder (28) as far as possible in the direc-
tion of rotation and take the filter holder, together with
the main filter (20) , out of the top part of the vacuum
cleaner (10) .
– Brush the folds of the main filter (20) with a soft brush.
or
Replace the main filter (20) if damaged.
– Place the filter holder (28) , together with the main filter
(20) , over the filter basket (29) and turn the filter holder
(28) as far as possible in the direction of rotation .
– Put the top part of the vacuum cleaner (10) on and close
the catches (9) .
Cleaning the wet filter
To prevent mould growth after wet vacuuming:
– Open the catches
(9) and remove the top part of the va-
cuum cleaner (10) (see figure C ).
– Leave the top part of the vacuum cleaner (10) to dry thor-
oughly.
– Pull the wet filter (21) out of the filter basket (29) .
– Wash the wet filter (21) under running water and then
leave it to dry thoroughly.
– Place the wet filter (21) completely over the filter basket
(29) .
– Put the top part of the vacuum cleaner (10) on and close
the catches (9) .
Storage and Transport (see figure J1–J2)
– Wrap the power cable around the carrying handle (12) .
– Place the suction tubes (26) in the holders (14) .
– Place the vacuum hose (15) in the holder (11) around
the top part of the vacuum cleaner.
– Carry the vacuum cleaner by the carrying handle (12) or
pull the vacuum cleaner along behind you on even sur-
faces using the pull strap
(4) .
– Store the vacuum cleaner in a dry room and secure it so
that it cannot be used by unauthorised persons.
– Put the castor brake (5) down to hold the castors (6) in
place.
Rectifying faults
u
If a fault (e.g. a filter damage) occurs, the vacuum
cleaner must be switched off immediately. The fault
must be repaired before resuming operation.
Problem Corrective measures
The suction turbine will not switch on. – Check the mains cable, mains plug, fuse and socket.
The mode selector switch (1) is set to "automatic start/stop".
– Set the mode selector switch (1) to the "extraction" symbol or switch on the
power tool plugged into the electric socket (2) .
The suction turbine will not switch
back on after the container has been
emptied. – Switch the dust extractor off and wait five seconds before switching it back on.
The suction power is decreasing. – Empty the container (7) .
– Remove any blockages from the extraction nozzle, suction tube (26) , vacuum
hose (15) or main filter (20) .
– Change the plastic bag (19) or dust bag.
– Make sure the filter holder (28) is engaged correctly.
– Place the top part of the dust extractor (10) on correctly and close the catches
(9) .
– Change the pre-filter (22) , main filter (20) or wet filter (21) .
Dust is escaping during extraction – Check that the main filter (20) has been fitted correctly.
– Change the main filter (20) .
Automatic switch-off (wet extraction)
is not working. Automatic switch-off will not work in the presence of non-conductive liquids or foam-
ing.
1 609 92A 4CP | (09.11.2018) Bosch Power Tools