7
1.
When the fan is switched off, press the
1
button and hold it
for approx. 4 seconds. The setting is displayed.
2.
Press the + or - button to change the setting of the sensor
control.
3.
To confirm the entries, press and hold the
1
button for
approx. 4 seconds.
Fan run-on time
The fan run-on time is possible at every fan setting (except
boost
‚
and boost
ƒ
).
Select the desired fan setting and press the
r
button.
Š
min
r
appears on the display.
Once this time has elapsed, the fan switches off automatically.
Setting the run-on time
When
Š
min
r
appears on the display, press the + or - button.
You can set a run-on time of between 1 and 9 minutes.
Lighting
The lighting can be switched on and off independently of the
fan.
Press the
B
button.
Setting the brightness
Press and hold the
B
button until the desired brightness is
reached.
Saturation display
When the metal mesh grease filters or the activated carbon
filter are saturated, a signal sounds for approx. 4 seconds after
the fan is switched off.
In addition, the corresponding symbol appears in the display:
■
Metal mesh grease filter:
#
■
Activated carbon filter:
’
#
If you have not yet done so, the metal mesh grease filters
should be cleaned or the activated carbon filter changed now.
For instructions on how to clean the metal mesh grease filters,
please refer to the section
Cleaning and maintenance
.
While the saturation displays are flashing, they can be reset. To
do this, press the – button.
Switching over the display for circulating-air mode
For circulating-air mode, the electronic control display must be
switched over accordingly:
■
The extractor hood must be connected and switched off.
■
Press the
%
and
r
buttons at the same time until the
™
#
display for starter sets for circulating-air mode or
’
#
display for CleanAir circulating air modules
lights up.
■
Repeatedly press the button combination to switch the
electronic control display back to exhaust air mode (
#
display).
Audible signal
Switching on the acoustic signal
When the fan is switched off, press the
%
and + buttons at the
same time for approx. three seconds. An acknowledgement
signal sounds.
Switching off the acoustic signal
Repeat the "Switching on the acoustic signal" process.
Cleaning and maintenance
:
Risk of burns!
The appliance will become hot during operation, especially
near the bulbs. Allow the appliance to cool down before
cleaning.
:
Risk of electric shock!
Penetrating moisture may result in an electric shock. Clean the
appliance using a damp cloth only. Before cleaning, pull out the
mains plug or switch off the circuit breaker in the fuse box.
:
Risk of electric shock!
Penetrating moisture may cause an electric shock. Do not use
any high-pressure cleaners or steam cleaners.
:
Risk of injury!
Components inside the appliance may have sharp edges. Wear
protective gloves.
Cleaning agents
Observe the information in the table to ensure that the different
surfaces are not damaged by using the wrong type of cleaning
agent. Do not use
■
harsh or abrasive cleaning agents,
■
cleaning agents with a high concentration of alcohol,
■
hard scouring pads or sponges,
■
high-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
Follow all instructions and warnings included with the cleaning
agents.
Area
Cleaning agents
Stainless steel
Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth.
Clean stainless steel surfaces in the
direction of the grain only.
Special stainless steel cleaning prod-
ucts are available from our after-sales
service or from specialist retailers.
Apply a very thin layer of the cleaning
product with a soft cloth.
Painted surfaces
Hot soapy water:
Clean using a damp dish cloth and
dry with a soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and
plastic
Glass cleaner:
Clean with a soft cloth.
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Operating controls Hot soapy water:
Clean using a damp dish cloth and
dry with a soft cloth.
Risk of damage to the electronics
from penetrating moisture. Never
clean operator controls with a wet
cloth.
Do not use any stainless steel cleaners.
