manualshive.com logo in svg

Bosch DSDA ISCSI DISK ARRAY SERIES DSA-N2B20, Руководство по установке

Поделиться
Скачать
Bosch DSDA ISCSI DISK ARRAY SERIES DSA-N2B20 Скачать руководство пользователя страница 26

24

en | Monitoring and Maintenance

DSDA iSCSI Disk Array Series

V 1 | 2008.08

Installation Guide

Bosch Security Systems

7.2

Maintenance

7.2.1

Disk Replacement DSA-S5B50

Follow these steps to replace a disk:

1.

Remove the new disk drive from the antistatic bag.

2.

Determine the disk drive to be replaced, see 

Section 7.5.1 DSA-S5B50

, page 30.

3.

Press the release latch of the drive. Swing the drive bay cover to the right until it is at a 

right angle to the chassis.

4.

Slide the entire assembly toward you in order to pull it out of the drive bay.

5.

Press the release latch of the new replacement drive. Swing the drive bay cover to the 

right until it is at a right angle to the chassis.

6.

Slide in the drive carrier and close the drive bay cover.

The drive LED should be lit 

green

 now.

7.2.2

Disk Replacement DSA-N2B20 / DSA-N2B50

Follow these steps to replace a disk:

1.

Determine the disk drive to be replaced, see 

Section 7.5.2 DSA-N2B20 / DSA-N2B50

, 

page 30.

2.

Grasp and pinch the latch.

Содержание DSDA ISCSI DISK ARRAY SERIES DSA-N2B20









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды