Bosch D8125 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 48

background image

D8125

D8125 Operation and Installation Guide

Page 7

© 2004 Bosch Security Systems, Inc.

74-04247-000-N

Introduction

1.0

Introduction

This guide covers installation of the D8125 POPEX Zone Expansion Module for use with the D8126, D8127 and D9127
POPITs on the following Bosch Security Systems control panels:

• D9412G

•D7212G

• D9112

• D9412

•D7212

• D9112B1

• D7412G

•D7212B1

• D8112G1

• D7412

•D9124

• D8112G2

1.1

Guide Organization

This guide is divided up into four sections, which are summarized in the Table 1 below.

Section

Description

1

Introduction

– this chapter

2

Overview

– This chapter is intended to provide an overview of the Zonex System,

including operational specifications.

3

Installation

– provides installation instructions

4

Troubleshooting

– provides common problems and solutions to solve them.

Table 1: D8125 POPEX Operation and Installation Guide Organization

1.2

Other Literature Referenced

See the following for a more complete and detailed description of the D8125 POPEX Zone Expansion. They have been
included in the table below with their part number for easy ordering. Contact Bosch Security Systems if you need to order
additional literature.

N am e of Literature

Bosch Security

System s Part N um ber

D 9412G /D 7412G Program Entry G u ide

47775

D 9412G /D 7412G O peration and Installation

43488

D 7212G Program Entry G uide

4998138538

D 7212G O peration and Installation

4998138544

O w ner’s M anual

varies

PO PIT Labels – 9000 Series

79-07675-000

Security System O w ner’s M anual

74-06633-000

Security System U ser’s G uide

74-06141-000

CO M EX Program Entry G u ide

74-05073-000

D 1252A Security System U ser’s G uide

71-04415-000

D 6500 Report D irectory

4998132019

O m egalarm D 8112 Zonex System Program /A ccount Record Sheet

74-06608-000

D 5060 M ultiplex Point P rogram m er U ser’s G uide

35262

Table 2: Referenced Literature

«
...
5
6
7
8
9
...
»

Содержание D8125

















































Отзывы:

Нет отзывов

Похожие инструкции для D8125

Бренд: ABB Страницы: 63

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 2

Бренд: Camozzi Страницы: 64

ROBO Cylinder RCP2 Series

Бренд: IAI Страницы: 5

Бренд: Lamtec Страницы: 22

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: Neles Страницы: 12

Бренд: Taco Electronic Solutions Страницы: 28

Бренд: Grundfos Страницы: 20

Бренд: Belimo Страницы: 2

Бренд: Watts Страницы: 12

Бренд: LCT Страницы: 5

Бренд: Hunter Страницы: 2

Бренд: jablotron Страницы: 12

Бренд: National Instruments Страницы: 26

Бренд: Samcen Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды