Bosch CWH 1000 P Скачать руководство пользователя страница 19

Страница: 19 / 23

WARNIN

ARNIN

ARNING

LP & N

LP & NG ARE EXTREMEL

G ARE EXTREMEL

G ARE EXTREMELY FL

Y FL

Y FLAMMABLE SO

AMMABLE SO

TTTTTAKE EXTRA PRECA

AKE EXTRA PRECA

AKE EXTRA PRECAUTIONS WHEN

UTIONS WHEN

PERF

PERFORMIN

ORMIN

ORMIN G ANY W

G ANY W

G ANY WORK T

ORK T

ORK TO THE HEA

O THE HEA

O THE HEATER

TER

CT-25

page 1 of 1

rev 10/06

Bosch Water Heating

340 Mad River Park, Waitsfield, VT 05673

BBT

NORTH AMERICA CORPORATION

Bosch Group

REPLACING ELECTRO-MAGNET

MODELS:

1000P, 1600P
260PN, 425PN

Tools needed:

8mm or small adjustable wrench
17mm or large adjustable wrench

Removing Electromagnet

1. Turn off gas to the water heater.
2. Turn off water supply to the water heater using installer

supplied cold water isolation valve.

3. Remove front cover of water heater as per instructions

in the installation manual.

4. Using 8mm or adjustable wrench, loosen and remove

8mm nut and lead wire connected to electromagnet.

5. Using 17mm or adjustable wrench, loosen larger 17mm

nut and remove electromagnet from gas valve assem-
bly.

Installing Electromagnet

1. Insert replacement electromagnet into rear of gas valve

with spring and plunger end first.

2. Secure electromagnet into gas valve by tightening large

17mm nut. Do not over tighten.

3. Thread lead wire with 8mm nut into electromagnet and

tighten. Do not over tighten.

4. Reinstall front cover per instructions in the installa-

tion manual.

5. Reopen water and gas supplies and check for gas leaks

around the electromagnet fittings. Tighten nuts fur-
ther if a leak is found.

6. If no leaks are found, return heater to service.

Electromagnet location (view from bottom of heater)

FIGURE 1

8mm nut

17mm nut

Содержание CWH 1000 P
























Результаты поиска

Содержание CWH 1000 P

Отзывы:

Похожие инструкции для CWH 1000 P

Бренды по названию

Популярные бренды

Bosch CWH 1000 P, Сборник сервисных бюллетеней

Результаты поиска

Содержание CWH 1000 P

Отзывы:

Похожие инструкции для CWH 1000 P

Бренды по названию

Популярные бренды