Bosch AXT 2200 HP, Руководство по эксплуатации

Страница: 11 / 71

English - 1
Warning: Read these instructions carefully, be fa-
miliar with the controls and proper use of the ma-
chine. Please keep the instructions safe for later
use. Before using for the first time, ask for a prac-
tical demonstration.
Read instruction manual.
Danger – rotating blades, keep hands and feet out of
openings while the machine is running.
Before handling the cutter, switch off and remove the
plug from the mains supply. If the cable is damaged or
cut through while working, do not touch the cable but
immediately remove the plug from the mains supply.
Never use the machine with a damaged cable.
Do not operate this equipment in the vicinity of by-
standers. Keep bystanders a safe distance away from
the machine.
Wait until all machine components have completely
stopped before touching them.
Wear protective gloves, sturdy shoes and long trou-
sers.
Obtain and wear eye protection at all times while oper-
ating the machine.
During operation, do not reach into the feed intake 10 or the
discharge chute 6. The machine runs on for a few seconds
after being switched off.
Before switching on, the machine must be assembled according
to the enclosed instructions.
It is recommended for increased electrical safety to use a Resid-
ual Current Device (RCD) with a tripping current of not more
than 30 mA. Always check your RCD every time you use it.
Use only extension cables that are intended for outdoor use and
are protected against splashes of water.
Do not touch the plug or socket with wet hands.
Do not drive over, crush or stretch the cable.
Do not allow children to operate this equipment.
Other persons and animals should remain at a distance of 3 me-
tres or more when the machine is being used. The operator is re-
sponsible for third persons in the working area.
Bosch can assure flawless functioning of the machine only when
original accessories are used.
Become familiar with the owner’s manual before attempting to
operate this machine.
Avoid wearing loose-fitting clothing, hanging cords or ties.
Only operate the machine in open space (e.g. not too close to a
wall or other fixed objects) and on a firm, level surface.
Do not operate the machine on paved or gravel surface where
ejected material could cause injury.
Before starting the machine, check that all screws, nuts, bolts
and other fasteners are properly secured and that guards and
screens are in place. Replace damaged or unreadable warning
and operating labels.
Before starting the machine, make certain that the feed intake is
empty.
Keep your face and body away from the feed intake.
Do not allow hands or any other part of the body or clothing in-
side the feed intake, discharge chute or near any moving part.
Switch off the machine before attaching or removing the bag.
Keep proper balance and footing at all times. Do not overreach.
Never stand at a higher level than the base of the machine when
feeding material.
Always stand clear of the discharge zone when operating the
machine.
When feeding material into the machine be extremely careful
that pieces of metal, rocks, bottles, cans or other foreign objects
are not included.
If the cutting mechanism strikes any foreign object or if the ma-
chine should start making any unusual noise or vibration, imme-
diately switch off and allow the cutter to stop. Remove the plug
from the mains supply and take the following steps:
–
Inspect for damage.
– Replace or repair any damaged parts.
– Check for and tighten any loose parts.
Do not attempt to repair the machine unless you are qualified to
do so.
Do not allow processed material to build up in the discharge
zone; this may prevent proper discharge which can result in kick-
back of material through the feed intake.
If the machine becomes clogged, switch off and allow the cutter
to stop. Remove the plug from the mains supply before clearing
debris.
Keep all guards and deflectors in place and in good working con-
dition.
Do not tamper with the motor speed control settings. Contact a
Bosch approved service agent if a problem exists.
Keep the motor cooling vents clean of debris and other accumu-
lations to prevent damage to the motor or possible fire.
Do not transport the machine while the motor is running.
Switch off, allow the cutter to stop and remove the plug from the
mains supply whenever you leave the work area.
Do not tilt the machine while it is running.
Do not expose the machine to rain. Only store the machine in a
dry place.
Maintenance and storage
–
When the machine is stopped for servicing, inspection, or
storage, or to change an accessory, switch off and remove
the plug from the mains supply and allow the machine to
cool. Make sure that all moving parts have come to a com-
plete stop before making any inspections, adjustments, etc.
– Maintain the machine with care and keep it clean.
– Replace worn or damaged parts for safety. Ensure all re-
placement parts are Bosch Approved.
– If an extension cord is used it shall not be of lighter grade
than the supply cord already fitted to the machine.
– Check the supply and any extension cord regularly for dam-
age or signs of ageing.
Do not use the machine, if the cords are damaged.
– When servicing the cutter be aware that, even though the
motor will not start due to the interlock feature of the guard,
the cutter can still be moved if the motor is turned by hand.
– Never attempt to override the interlock feature of the guard.
Safety Notes
STOP
F016 L70 439 - book.book Seite 1 Dienstag, 28. Februar 2006 7:57 07
11 • F016 L70 439 • TMS • 06.02