Bosch AquaStar 125B LPS Скачать руководство пользователя страница 15

15

6 720 606 518

To test the thermocouple, disconnect the thermocouple lead
to the ECO. Insert a multi-meter probe into the thermocouple
lead and attach or hold the other lead to the metal gas
valve (DC common). Light the pilot flame and hold button,
meter reading should be 24 mVDC or more. If the reading is
24 mVDC or more the thermocouple is good. To test the
electromagnet, re-connect the thermocouple lead to the
ECO, light pilot and hold button while taking a reading
between the ECO leads and the metal gas valve (DC
common). The reading should drop to 19 mVDC or less. If it
does not, replace the electromagnet.

BURNERS DO NOT IGNITE WHEN HOT WATER IS TURNED
ON

1. Pilot is not on.

Light the pilot. See lighting instructions.

2. Gas valve button not positioned on Burner Position

Be sure once the  pilot flame is on, that after a 15 to 20
second wait, the main burner button (        ) is pushed all the
way in.

3. Cold incoming water connection made to wrong side

of heater

Make sure cold water inlet connection is on the right side of
heater when you are facing the heater.

4.

Water flow rate at hot water tap is too low.

Note:

 The AquaStar models 125B”S” require 0.5 gallon per

minute flow to activate the burners. This is a flow which
would fill a quart jar in 30 seconds.

5. Cold water inlet filter on heater is dirty.

Remove filter and clean. This screen filter is located at the
inlet side of the brass water valve (fig. 11, #34). Check and
clean faucet aerators too.

6. Crossover in household plumbing

The AquaStar burner activates when there is sufficient water
pressure drop in the AquaStar water valve assembly — ie.
when a hot water faucet is opened. If there is a crossover in
the plumbing, the necessary pressure drop in the AquaStar
will be insufficient, or totally eliminated. A plumbing crossover
can be caused by a bad washer at a single lever faucet or
incorrect plumbing or a mixing valve in the line, etc. which
permits hot and cold water to mix in the plumbing. The
crossover will create a back pressure in the system preventing
the pressure drop in the Aquastar — i.e. cold water is entering
the water heater from both sides and the burners will not
come on. To confirm there is no crossover in the plumbing,
shut off the cold water supply to the AquaStar. Open your
hot water taps. There should not be any water flowing. If
there is water flowing, there is a crossover in the plumbing.
This is a plumbing problem, not an Aquastar problem. Please
contact your plumber.

7. Water valve parts may be dirty or components

damaged.

Water valve and component parts must be totally free of
dirt. First check that the venturi is free of dirt particles. In
hard water areas, mineral deposits can eventually (3 to 5
years in hard water areas) corrode the water valve parts to
a point where they will need replacing.

Any sign of moisture or corrosion at the joint of the water
valve and the gas valve is a sign that the water valve assembly
components need to be replaced immediately

.

Note:

 Water valve for model 125B”S” is part # 8707002393

for both LP and NG models. (Contact service person to
clean water valve or replace if corrosion is present).

PILOT LIGHT GOES OUT DURING OR IMMEDIATELY
AFTER HOT WATER HAS BEEN USED

1. Gas pressure too low

Very low gas pressure may be caused by low delivered gas
pressure, a jammed gas regulator or undersized gas lines. If
the gas lines are undersized, there may still be the specified
static gas line pressure. However when the water valve
opens,and gas enters the burners, the pressure could drop
sharply, causing the pilot flame to go out.
Have a gas technician confirm the gas pressure both static
and at maximum Btu output. Specifications for your heater
are on page 2.

2. Pilot may be dirty or weak

See Page 13 for instructions on pilot maintenance.

3. Burners are not shutting down immediately when hot

water is turned off

Note:

 If burners don’t shut down immediately when the hot

water is turned off, the heater will overheat and the ECO
will shut-off the gas. Rebuild the water valve assembly using
the repair kit from BBTNA (part #8 703 406 204).

WATER IS TOO HOT

1

.

Water flow rate is too low.

Increase the flow rate.

2. Not enough cold water mixing at faucet

Contact your plumber to adjust mixing valves on faucets.

3. The heater’s fixed degree rise is too high for user

The calibration nut for the thermostat assembly at the gas
valve can be adjusted upward to lower the temperature rise.
A seal of paint coats two adjusting nuts there, the thin up-
per one is a lock nut while the lower one is the adjuster.
Loosen the lock nut one first.  Tighten the adjuster nut in-
crementally upward and check water temperature, stop when
satisfactory.  Then tighten down the lock nut. 

     Caution:

Never back the adjuster nut downward to the last thread
unless the thermostat is being replaced.  This is a gas

seal.

WATER IS NOT HOT ENOUGH

1. Water flow rate is too high.

Decrease the flow rate.

2. Btu input is too low due to insufficient gas pressure

It is extremely important for a tankless instantaneous
water heater to have the right size gas line to obtain
the correct gas pressure

Содержание AquaStar 125B LPS

























Отзывы: