18
| English
1 609 92A 138 | (24.2.15)
Bosch Power Tools
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, until 19 April 2016:
2004/108/EC, from 20 April 2016 on: 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-2.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 24.02.2015
Assembly
Before any work on the power tool, remove the battery.
Battery Charging
Use only the battery chargers recommended by Bosch
for this power tool.
Only these battery chargers are
matched to the lithium ion battery used in your machine.
Note:
The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the On/Off switch after the
machine has been automatically switched off.
The bat-
tery can be damaged.
Observe the notes for disposal.
Removing the battery (see figures A1 – A2)
The battery
9
is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button
14
unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
– To remove the battery
9
, press the unlocking button
14
and pull out the battery toward the front.
Do not exert any
force.
Battery Charge-control Indication (yellow LED)
Operating and Storage Environment
The device is suitable exclusively for operation at enclosed
work sites.
For proper operation, the allowable ambient temperature
should be between 0 °C und +45 °C at an allowable relative
humidity between 20 and 95 %, free of moisture condensa-
tion.
Suspension Device (see figure B)
With the utility clip
15
, the machine can be attached to a sus-
pension device.
– Fasten the utility clip
15
to the machine by engaging it into
the fastening slots
16
.
Angled drive head
Straight
drive head
1/4"
3/8"
3/8"
1/4"
QC
1/4"
QC
1/4"
Article number 0 607 ...
... 453 617 ... 453 620 ... 451 618 ... 453 618 ... 453 630 ... 453 631
Maximum torque, hard screw-
driving application according to
ISO 5393
Nm
20
25
30
20
20
6
Tightening torque at the flange
Nm
20
20
25
20
20
10
Accessories for
ANGLE EXACT ION
15-500
15-500
30-300
15-500
15-500
15-500
Weight according to
EPTA-Procedure 01/2003
kg
0.2
0.2
0.3
0.2
0.2
0.2
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Battery Charge-
control Indica-
tion 8
Meaning
Flashing light +
audio signal
Battery Charging:
Only 6–8 more screwdriving operations
possible.
Continuous light
Capacity no longer sufficient for a new
screwdriving operation or the machine
was subject to overload:
The machine can no longer be switched
on.
– Remove the battery and replace with
a fully charged one.
Flashing light
The machine is overheated and out of
operation:
– Before restarting the operation of the
machine, wait until the flashing auto-
matically stops after a short period.
OBJ_BUCH-1521-005.book Page 18 Tuesday, February 24, 2015 2:30 PM
