English |
19
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
Battery charging
u
Use only the chargers listed in the technical data.
Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note:
The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
Do not continue to press the On/Off switch after the
power tool has automatically switched off.
The battery
can be damaged.
Removing the battery
To remove the battery
(6)
, press the release button
(5)
and
pull the battery back and out of the power tool.
Do not use
force to do this.
Battery charge indicator
When the on/off switch
(10)
is pressed in halfway or com-
pletely, the battery charge-control indicator
(8)
indicates
the charge condition of the battery for several seconds. The
indicator consists of three green LEDs.
LED
Capacity
Continuous lighting 3 x green
≥ 66%
Continuous lighting 2 x green
33–66%
Continuous lighting 1 x green
11–33%
Slowly flashing light 1 x green
≤ 10%
The three LEDs in the battery charge indicator flash
quickly when the temperature of the battery is outside
the operating temperature range of –30 to +65 °C and/or
the overload protection has been triggered.
Changing the Tool
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
Inserting the application tool (see figure A)
Insert the application tool all the way into the holder
(1)
.
Fitting the adapter (see figure B)
Remove the application tool.
Insert the adapter into the holder
(1)
. The adapter clicks
audibly into place.
Inserting the application tool into the adapter (see figure
C and D)
Insert the application tool all the way into the holder
(1)
. The
application tool is held in the holder by means of a magnet.
Drill chuck adapter (see figure E)
Open the drill chuck adapter
(11)
by turning it in the direc-
tion of rotation
➊
until the application tool can be inserted.
Insert the application tool.
Firmly tighten the sleeve of the drill chuck adapter
(11)
by
turning it by hand in the direction of rotation
➋
. This will
automatically lock the drill chuck.
Turning the adapter (see figure F)
Remove the adapter from the power tool. Turn the adapter
to the required position and then reattach it.
Removing the adapter (see figure G)
Remove the application tool.
Pull the adapter off the mounting
(1)
.
Combining adapters (see figure H)
Insert the angle screw adapter
(13)
into the mounting
(1)
.
Then insert the drill chuck adapter
(11)
into the angle screw
adapter
(13)
.
Bosch Power Tools
1 609 92A 4SE | (12.04.2019)
Содержание AdvancedImpact 18 QuickSnap
