Borroughs BASIC PRO SERIES Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 17

background image

16

Figure 12.

GO TO SECTION #1, STEP #7

*NOTICE*

The following is the only warranty applicable to the products: the manufacturer warrants that the products are free from
defects in material or workmanship when installed, used and serviced in accordance with the manufacturer’s
recommendations.  The manufacturer’s only obligation under this warranty shall be to replace any product, which is defective
in materials within one year or defective in workmanship within ninety days, from the date of installation.  THE
FOREGOING WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PURPOSE.  The manufacturer shall not
be liable for any loss or damage, direct of indirect, resulting from the use or loss of use of the product.  This warranty may
not be changed except by a written agreement signed by an officer of the manufacturer.

«
...
14
15
16
17
»

Содержание BASIC PRO SERIES


















Отзывы:

Нет отзывов

Похожие инструкции для BASIC PRO SERIES

Camedia MAUSB-100

Бренд: Olympus Страницы: 2

Z-DRIVE R2 M84 512GB PCI-EXPRESS SSD

Бренд: OCZ Страницы: 2

So Mobile SuperSpeed

Бренд: DANE-ELEC Страницы: 1

Бренд: Hanover Страницы: 27

Бренд: SanDisk Страницы: 7

Бренд: Orico Страницы: 27

Бренд: Holzmann Страницы: 20

CLARiiON CX4-120

Бренд: EMC Страницы: 62

Бренд: LevelOne Страницы: 85

Бренд: Galvo Shed Страницы: 8

Бренд: Qualstar Страницы: 205

Бренд: Oracle Страницы: 268

Бренд: ABSCO SHEDS Страницы: 22

Бренд: Dancover Страницы: 30

Бренд: Supatool Страницы: 2

G-SPEED SHUTTLE

Бренд: G-Technology Страницы: 8

Бренд: G-Technology Страницы: 27

Бренд: G-Technology Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды